AT&T 5840 user manual Feature Setup Handset, Feature Setup Menu, Set Time

Page 11

5840_CIB_2ATT 2002.11.7 5:47 PM Page 8

FEATURE SETUP – HANDSET

FEATURE SETUP – HANDSET

Feature Setup Menu

Press the softkey under

MENU to enter the Feature

Setup menu. Use

or

to choose

features, then select

OK

to save your choice.

NOTE: If you wait more than 20 seconds without pressing a key, the handset returns to

the idle screen.

NOTE: If you receive an incoming call while in

feature setup, the phone automatically exits the menu to take the call.

Set Time

i i i

You can choose to set the time manually, or you

can allow it to be set automatically with incoming

 

Caller ID information.

 

1

Press

MENU .

 

2

Press

until the screen displays

CALLS LOG

INTERCOM

HANDSET SETTINGS

SET TIME

 

 

 

OK

3

Press

OK

. The screen displays the

 

current time setting. Use

 

to move

 

the cursor, and use the keypad to change a

 

digit. Select

AM/PM .

 

 

4

Press

SAVE

to save the displayed time.

NOTE: To set up the answering system clock, please see ANSWERING SYSTEM OPERATION on

page 50 in this manual.

8

Image 11
Contents Part 1 Important Product Information With Caller ID/Call WaitingAdvanced American Telephones. All Rights Reserved Contents Before YOU Begin Parts ListBefore YOU Begin About Adding Handsets About Caller Identification Caller IDAbout the Calls Log Connect the telephone line cord Connect the power cord InstallationInstallation Table/Desk InstallationCheck for dial tone Install the handset batteryCharge the handset battery Follow Steps 3-5 in Table/Desktop Installation Wall InstallationSpare Battery/Power Failure Backup Headset Belt ClipSet Time Feature Setup HandsetFeature Setup Handset Feature Setup MenuClock Mode Sound Select Ringer Volume Ringer Melody #01OFF Vibrate ControlHighlights LOW Batt Tone Low Batt ToneRange Tone Keypad Tone Feature Setup HandsetSet Contrast English Language SettingFeature Setup Base Feature Setup BasePress Menu . Use To highlight Base SETTINGS, then press Dial Mode Tone/Pulse Contrast Language At the Handset Telephone OperationMake a Call Answer a CallBase Speaker VolumeTelephone Operation HandsetAnswer a Call Switch Between Handset and SpeakerphoneHandset Speakerphone Make a CallDialing Options Base SpeakerphoneDelete a Redial Number RedialSave a Redial Number Base Flash/Call WaitingMute Hold Temporary Tone Dialing Screen Displays When Display Screen MessagesThis Icon Indicates Handset IconsLight Status Indicates Base IconsBase Lights One beep Tones and What They MeanTone Indicates Three quick beepsIntercom Calls Intercom OperationIntercom Operation Answer an Incoming Call While on an Intercom Call Answering IntercomEnd Intercom From the Handset Blind Call TransferConference Calling Phone Book Phone BookKeypad Characters Dial a Number in Phone Book GeorgeEdit a Number/Name in Phone Book GeorgeDelete a Number/Name in Phone Book Caller ID Operation Caller ID OperationStore Record in Phone Book Caller ID OperationReview Calls Log Display Dial Removing All Records Remove Call RecordsRemoving a Specific Call Record Turn Answering System On/Off Audible IndicatorsAnswering System Operation Answering System Operation AT the BaseAbout Announcements About MailboxesRecord Your Announcement Answering System OperationAnswering System Feature Setup System Announces DESCRIPTION/DIRECTIONS Feature SummaryDelete Messages Listen to, Save & Delete MessagesPlay Messages Call Screening/Intercept Adjust Playback VolumeRecord a Memo Window Displays When Message Window DisplayVoice Menu Connect with the Answering SystemFunction Command Remote Access CommandsBatteries Battery LifeBattery Indicator Charge the Handset Battery PackSpare Battery Replace the Handset Battery Pack Phone CaseCase of Difficulty To re-initialize the handset and base If you hear noise or interference when using the phoneIf your telephone Problem SolutionIf the phone does not ring when you receive a call DifficultyIf the caller’s name or phone number is not displayed Caller IDIncomplete Answering SystemIf messages are Clear Case of DifficultyIf your outgoing Announcement isn’tFunction Default Setting Default SettingsDefault Settings Default SettingsTechnical Specifications Technical SpecificationsTechnical Specifications Index IndexKeypad Tone TONE/PULSE