AT&T 5840 user manual To re-initialize the handset and base

Page 68

5840_CIB_2ATT 2002.11.7 5:50 PM Page 65

PHONE

PROBLEM

To re-initialize the handset and base:

SOLUTION

1 Disconnect the power to the base.

2 Remove spare battery pack (if installed).

3 Remove the handset battery pack.

4 Wait at least 15 seconds.

5 Insert the handset battery pack.

6 Connect the power to the base.

PROBLEM

If you hear noise or interference when using the phone:

SOLUTION

You may be out of range. Move closer to the base.

Household appliances plugged into the same circuit as the base can sometimes cause interference. Try moving the appliance or the base to another outlet.

The layout of your home or office may be limiting the operating range. Try moving the base to another location, preferably on an upper floor.

Using the handset near household appliances (microwaves, computers, televisions, stereos, etc.) can sometimes cause interference. Move away from appliances while using the handset.

IN CASE OF DIFFICULTY

65

Image 68
Contents With Caller ID/Call Waiting Part 1 Important Product InformationAdvanced American Telephones. All Rights Reserved Contents Before YOU Begin Parts ListBefore YOU Begin About Adding Handsets About Caller Identification Caller IDAbout the Calls Log Installation InstallationTable/Desk Installation Connect the telephone line cord Connect the power cordCheck for dial tone Install the handset batteryCharge the handset battery Wall Installation Follow Steps 3-5 in Table/Desktop InstallationSpare Battery/Power Failure Backup Belt Clip HeadsetFeature Setup Handset Feature Setup HandsetFeature Setup Menu Set TimeClock Mode Sound Select Ringer Volume #01 Ringer MelodyVibrate Control OFFLow Batt Tone Highlights LOW Batt ToneRange Tone Feature Setup Handset Keypad ToneSet Contrast Language Setting EnglishFeature Setup Base Feature Setup BasePress Menu . Use To highlight Base SETTINGS, then press Dial Mode Tone/Pulse Contrast Language Telephone Operation Make a CallAnswer a Call At the HandsetVolume Telephone OperationHandset Base SpeakerSwitch Between Handset and Speakerphone Handset SpeakerphoneMake a Call Answer a CallBase Speakerphone Dialing OptionsDelete a Redial Number RedialSave a Redial Number Flash/Call Waiting BaseMute Hold Temporary Tone Dialing Display Screen Messages Screen Displays WhenHandset Icons This Icon IndicatesLight Status Indicates Base IconsBase Lights Tones and What They Mean Tone IndicatesThree quick beeps One beepIntercom Calls Intercom OperationIntercom Operation Answer an Incoming Call While on an Intercom Call Answering IntercomEnd Intercom Blind Call Transfer From the HandsetConference Calling Phone Book Phone BookKeypad Characters George Dial a Number in Phone BookGeorge Edit a Number/Name in Phone BookDelete a Number/Name in Phone Book Caller ID Operation Caller ID OperationStore Record in Phone Book Caller ID OperationReview Calls Log Display Dial Removing All Records Remove Call RecordsRemoving a Specific Call Record Audible Indicators Answering System OperationAnswering System Operation AT the Base Turn Answering System On/OffAbout Mailboxes About AnnouncementsAnswering System Operation Record Your AnnouncementAnswering System Feature Setup Feature Summary System Announces DESCRIPTION/DIRECTIONSDelete Messages Listen to, Save & Delete MessagesPlay Messages Adjust Playback Volume Call Screening/InterceptRecord a Memo Message Window Display Window Displays WhenConnect with the Answering System Voice MenuRemote Access Commands Function CommandBattery Life Battery IndicatorCharge the Handset Battery Pack BatteriesSpare Battery Replace the Handset Battery Pack Phone CaseCase of Difficulty If you hear noise or interference when using the phone To re-initialize the handset and baseProblem Solution If the phone does not ring when you receive a callDifficulty If your telephoneCaller ID If the caller’s name or phone number is not displayedIncomplete Answering SystemIf messages are Case of Difficulty If your outgoingAnnouncement isn’t ClearDefault Settings Default SettingsDefault Settings Function Default SettingTechnical Specifications Technical SpecificationsTechnical Specifications Index IndexKeypad Tone TONE/PULSE