Polycom P001 Setting and Using Camera Presets, Points to note about camera control and layouts

Page 17

User’s Guide for the Polycom RealPresence Group Series

Setting and Using Camera Presets

Camera presets are stored camera positions that you can create ahead of time or during a call. The system uses preset 0 as the default camera position for all preset camera positions. This default camera position is zoomed out, panned straight ahead with horizontal tilt.

Presets allow you to:

•Quickly point a camera at pre-defined locations in a room.

•Select a video source such as a document camera or an auxiliary camera.

If your system’s camera supports pan, tilt, and zoom movement, you can create up to 10 preset camera positions for the near-end camera. Each preset stores the following information:

•Camera number

•Camera zoom level

•Direction the camera points

These presets remain in effect until you change them.

If far-end camera control is allowed, you can create 10 presets for the far-end camera. These presets are saved only for the duration of the call. You may also be able to use presets that were created at the far end to control the far-end camera.

Points to note about camera control and layouts:

•When in a call, selecting near camera control pans and zooms the local camera without changing the layout.

•When out of a call, selecting camera control changes the self-view from Picture-In-Picture (PIP) to full screen.

•Incoming calls override the full-screen self-view layout.

To view stored presets:

>>Select > Cameras > Presets. Icons for presets 1-10 are shown on the screen.

To move the camera to a stored preset:

1Select > Cameras > Presets.

2Press a number on the remote control or navigate to the snapshot and select it.

Polycom, Inc.

13

Image 17

Contents User’s Guide for the Polycom RealPresence Group Series Patent Information Trademark InformationContents User’s Guide for Polycom RealPresence Group Series Contents User’s Guide for the Polycom RealPresence Group Series Using the Remote Control To recharge the remote control battery Recharging the Remote Control BatteryPower On Self Test Post Powering On and OffTo open the Menu screen Navigating the Local User InterfaceTo return to the Home screen Placing a Call Calling and AnsweringCalling by Entering a Name or Number Place a Call Recent Calls Place a Call ContactsCalling from the Contacts Screen Calling from the Recent Calls ListGo to Place a Call and select Recent Calls Go to Place a Call and select ContactsEnding a Call Answering a CallTypes of Video Calls You Can Make Calling a Speed Dial EntryViewing Your System’s IP Address Controlling What You SeeParticipating in an Encrypted Call A call Selecting and Adjusting a Camera or Other Video SourceOut of a call To adjust a Polycom EagleEye View camera To stop camera tracking To start camera trackingTo view stored presets Setting and Using Camera PresetsTo move the camera to a stored preset Select Cameras PresetsControlling What You Hear Switching Between Full-Screen Video and the Home ScreenAdjusting Volume Enjoying Stereo Audio in Video Calls Muting the MicrophoneTo mute or unmute the microphone Points to note about muting the microphoneShowing Content with People+Content IP Showing ContentInformation System Detail ResolutionClick Disconnect Refresh rates HzRealPresence Group 500 System Resolution Refresh rates HzTo set up your RealPresence Group system to show content To stop showing content Points to note about showing contentSearching for Directory Contacts Working with Directory and Contact EntriesIncluding Multiple Sites in Calls To place a multipoint call using Recent CallsPlacing a Multipoint Call To place a multipoint call by adding sites to a callHanging Up a Multipoint Call Passwords for Multipoint CallsTo configure a meeting password To enter a meeting passwordMultipoint Viewing Layouts To change layouts during a multipoint callChanging the Way Calls Are Answered Temporarily Refusing CallsAnswering Video Calls Automatically To temporarily refuse incoming callsSelect Mute Auto Answer Calls Muting Automatically Answered Video CallsTo mute automatically answered video calls User’s Guide for the Polycom RealPresence Group Series Using Microsoft Outlook Calendaring Joining a Scheduled Meeting Viewing Scheduled MeetingsIcon Presence Description To activate call forwarding Using Avaya Network Features with Video CallsMuting in a Cccp Call To add a system to a call To deactivate call forwardingTo transfer a call Customizing Your Workspace Adjusting for Room LightingAllowing the Far-End System to Control Your Camera Select Far Control of Near CameraAllowing Video Display on the Web TroubleshootingPlacing a Test Call To allow the display of video on the webStatus System InformationSelect Information Select StatusA Call Status Information Status Screen DescriptionTo access information about your system diagnostics System DiagnosticsSelect Diagnostics Diagnostic Screen DescriptionPlay the VCR or DVD to test the audio Contacting Technical and Solution Support Using the Knowledge BaseSearching Documentation Polycom Technical SupportRegulatory Notices Polycom Solution SupportPolycom RealPresence Group System 700 Regulatory Model P002