Aiphone IS operation manual Outline of Operations, Is-Ccu

Page 11

OUTLINE OF OPERATIONS

This manual mainly describes the following operations.

•Operations you can do within a site (communication, transferring, paging, monitoring, door release, etc.)

•Operations you can do between sites (communication, transferring, paging, door release, etc.)

•Telephone operations and other telephone-related operations (North America only)

	Telephone
Site 1	: Control ofﬁce, etc.
	IP

PSTN / private line (North America only)

Internet / WAN

Communication,

GETTING

release, etc.

transferring,

Site 3

Site 4

paging, door

Standard (IP) system

Site 2

Standard (IP) system

Site 32

STARTED

PBX telephone

PBX telephone

LAN (IP network)

LAN (IP network)

SETTING

IPIS-IPC

IP

IP

IP

IP

IP

IP

IP

IP

IS-IPC

IS-IPC

AND

transferring, paging,

IS-CCU

ADJUSTMENT

Building B

Communication,

IS-CCU

Building E

Communication,

transferring,

IS-RCU

IS-RCU

IS-SCU

IS-SCU

monitoring, door

paging, door

release, etc.

release, etc.

IS-RCU

IS-RCU

USING THE

Building C

Building D

SYSTEM

Building A

Local system

IP IP unit

The pilot station or zone that receives a call, paging, etc. from a remote site.

NOTES:

•The arrows in the ﬁgure above show examples of operations.

•For the available functions and operations in a local system, refer to the “OPERATION MANUAL” for the local system.

•For operating a PC master station (IS-SOFT), refer to the “OPERATION MANUAL” for the PC master station.

•You can communicate with the pilot station or page the pilot zone registered in a remote site. You cannot select a desired station or zone in a remote site.

•Depending on the system conﬁguration of a remote site, some operations to the site may be disabled.

•A call or talk may not be possible when the communication path is fully occupied.

•Video images at the target video door station may not appear on the monitor when the video path is fully occupied even though a call or talk is possible.

APPENDIX

11

Image 11

Contents 834174 B P0811JZ Standard IP SystemContents Viewing video images at Target station Paging Chime paging Calling another station Direct voice call MonitoringIntroduction PrecautionsGeneral Precautions Unit becomes inoperative during power failure Color monitor master station Part NamesDisplay item examples MonitorDisplay examples Standby modeVandal-resistant audio door station ﬂush-mount IS-SS Vandal-resistant door stationTransmit LED red Room sub station IS-RSIS-CCU Outline of OperationsCommunication You cannot monitor or scan-monitor a remote site Electric door strike Door station Room sub station Setting items Master Station Settings and AdjustmentsAdjusting sound volume Tone VOL Adjusting screen brightness BrightnessRoom SUB Call Tone Initial settings Initial SettingBasic setting procedure Setting the call-in tones Door Call ToneSub items are displayed Setting the display modes of the monitor DisplayYou can make the following settings for the display modes Press to select the desired search item so thatSchedule Transfer Transfer DelayCall Transfer PRIVACY-2 Call Tone Privacy ModeTelephone Transfer Lights up Receiving a callCall tone rings, and the corresponding display appears Answer the call in one of the following ways Communication in the hands-free modeCommunication in the press-to-talk mode When called in from a sub stationPress-to-talk mode Communication by using the handsetWhen two or more calls have arrived IS-MV Hands-free modeWide Zoom Switching Zoom/WideViewing video images at a video door station Pan & TiltPress Adjust again Adjusting imagesPress Adjust when the image is difﬁcult to see To restore the image before adjustmentCall transferring When both 1 and 3 are set, 3 takes priorityCommunication transferring To communicate with the caller While receiving a callName Search →P Received Calls →P Standby modeSearch items Stations by Area →P Placed Calls →PRemote Site →P Search ListName Search →P Stations by Area →P Stations by Type →P Paging Zone →P Chime Zone →PYou cannot select two or more remote sites When searching for MASTER004 Press the dial keys as followsSearching for a station, zone or remote site from the list PressAll the station types are displayed in the list Select Stations by Type from the Search LIST. →PAll the stations in the area are displayed in the list You can select up to 5 stations. →PRemote Site You can select up to 5 stations and/or zones. →P Placed CallsPress to select Placed Calls in the standby mode. →P Press to select Received Calls in the standby mode. →PPage Press OFF or hang up the handset to ﬁnish communicating Calling another station direct voice callTo shift to scan-monitoring Viewing video images at the target stationMonitoring Scan-monitoringMaking chime paging automatically Communicating with telephone North America only Other FunctionsIt is also possible to set to stop the current chime paging Other functions combined with connected external devicesRoom sub station Central control unitAvailable Character List Technical PrecautionsSpecifications Vandal-resistant audio door station ﬂash-mount IS-SS Vandal-resistant video door station surface-mount IS-DVVandal-resistant video door station ﬂush-mount IS-DVF IP vandal-resistant video door station ﬂush-mount IS-IPDVFPower supply unit IS-PU-UL, IS-PU-S Object area of is the EU WarrantyFor US market For Canada market

Related manuals

Manual 28 pages 11.84 Kb