Aiphone IS Receiving a call, Call tone rings, and the corresponding display appears, Lights up

Page 21

USING THE SYSTEM

RECEIVING AND ANSWERING A CALL ON THE MASTER STATION

The following describes the communication method using this system.

*When receiving a call from a remote site, the operation methods are the same as described below, however it may take a longer time for some operations and their responses. For example, there may be a time difference between a call starting at a remote site and the call tone ringing on the target master station in your site.

Receiving a call

Door station	Room sub station	Another master station	PC master station
(in your site or a remote site)	(in your site or a remote site)	(in your site or a remote site)	(in your site or a remote site)

or

Press

or

Press or Lift the handset.

or

(See page 35 for	(See the “OPERATION
how to call from a	MANUAL” for the PC
master station.)	master station (IS-SOFT).

GETTING STARTED SETTING AND

1 The call tone rings, and the corresponding display appears.

*The call tone from a sub station differs from the setting. (→P. 17) e.g.) When called from a video door station

Lights up.

*1

The station no., station name and video image at the calling station (following the symbol image) are displayed.

(When called from a remote site, the site no., site name and video image at the calling station (following the symbol image) are displayed. The station name will not be displayed.)

*It may take long until a video image appears on the monitor.

*When an audio door station, room sub station or another master station calls in, the station type image is displayed. (The image differs from the calling station type.) When called from a remote site, the remote site symbol image is displayed.

*An incoming call from another master station will be a direct voice call. (However, when the PRIVACY MODE is set to “2”, you will be notiﬁed of an incoming call by the display information and call tone.)

*When you answer a call, the call tone of subsequent incoming calls should be muted until you conclude the ﬁrst call (except when using IS-IPMV).

*1: LIST

Press to display the list of stations when two or more calls are received. You can select the desired one and start communicating with the caller. (→P. 23)

NOTE:

An IS-IPMV cannot receive two or more calls at a time.

21

ADJUSTMENT USING THE SYSTEM

APPENDIX

Image 21

Contents 834174 B P0811JZ Standard IP SystemContents Viewing video images at Target station Paging Chime paging Calling another station Direct voice call MonitoringPrecautions General PrecautionsIntroduction Unit becomes inoperative during power failure Color monitor master station Part NamesDisplay item examples MonitorDisplay examples Standby modeVandal-resistant audio door station ﬂush-mount IS-SS Vandal-resistant door stationTransmit LED red Room sub station IS-RSIS-CCU Outline of OperationsCommunication You cannot monitor or scan-monitor a remote site Electric door strike Door station Room sub station Setting items Master Station Settings and AdjustmentsAdjusting sound volume Tone VOL Adjusting screen brightness BrightnessBasic setting procedure Initial settings Initial SettingSetting the call-in tones Door Call Tone Room SUB Call ToneYou can make the following settings for the display modes Setting the display modes of the monitor DisplayPress to select the desired search item so that Sub items are displayedTransfer Delay Call TransferSchedule Transfer Privacy Mode Telephone TransferPRIVACY-2 Call Tone Receiving a call Call tone rings, and the corresponding display appearsLights up Communication in the press-to-talk mode Communication in the hands-free modeWhen called in from a sub station Answer the call in one of the following waysWhen two or more calls have arrived IS-MV Communication by using the handsetHands-free mode Press-to-talk modeViewing video images at a video door station Switching Zoom/WidePan & Tilt Wide ZoomPress Adjust when the image is difﬁcult to see Adjusting imagesTo restore the image before adjustment Press Adjust againWhen both 1 and 3 are set, 3 takes priority Communication transferringCall transferring To communicate with the caller While receiving a callSearch items Standby modeStations by Area →P Placed Calls →P Name Search →P Received Calls →PName Search →P Stations by Area →P Stations by Type →P Search ListPaging Zone →P Chime Zone →P Remote Site →PSearching for a station, zone or remote site from the list When searching for MASTER004 Press the dial keys as followsPress You cannot select two or more remote sitesAll the stations in the area are displayed in the list Select Stations by Type from the Search LIST. →PYou can select up to 5 stations. →P All the station types are displayed in the listRemote Site Press to select Placed Calls in the standby mode. →P Placed CallsPress to select Received Calls in the standby mode. →P You can select up to 5 stations and/or zones. →PPage Press OFF or hang up the handset to ﬁnish communicating Calling another station direct voice callMonitoring Viewing video images at the target stationScan-monitoring To shift to scan-monitoringMaking chime paging automatically Communicating with telephone North America only Other FunctionsRoom sub station Other functions combined with connected external devicesCentral control unit It is also possible to set to stop the current chime pagingAvailable Character List Technical PrecautionsSpecifications Vandal-resistant video door station ﬂush-mount IS-DVF Vandal-resistant video door station surface-mount IS-DVIP vandal-resistant video door station ﬂush-mount IS-IPDVF Vandal-resistant audio door station ﬂash-mount IS-SSPower supply unit IS-PU-UL, IS-PU-S Warranty For US marketObject area of is the EU For Canada market

Related manuals

Manual 28 pages 11.84 Kb