Aiphone IS operation manual Call Transfer, Transfer Delay, Schedule Transfer

Page 19

ESetting the call transferring [TRANSFER]

You can make the following settings for transferring calls.

Sub item

Description

Setting range

[CALL

Enables (ON) or disables (OFF)

ON

TRANSFER]

the call transferring.

OFF

[TRANSFER

(Available when [CALL

(Registering a

DESTINA]

TRANSFER] is set ON.)

master station or

(Transfer

Selects a master station in your

a remote site)

destination)

site or a remote site as the

 

 

transfer target.

 

[TRANSFER

(Available when [CALL

00-60 (sec.)

DELAY]

TRANSFER] is set ON and the

 

 

target is set at [TRANSFER

 

 

DESTINA].)

 

 

Sets the time of starting

 

 

transferring after a call is received.

 

[SCHEDULE

Enables or disables the call

ON

TRANSFER]

transferring to be performed

OFF

 

on the schedule preset by the

 

 

system settings automatically.

 

[SCHEDULE

(Available when [SCHEDULE

(Registering a

DESTINA]

TRANSFER] is set ON.)

master station or

(Schedule

Selects a master station in your

a remote site)

destination)

site or a remote site as the

 

 

transfer target on the schedule.

 

[TELEPHONE

Enables (ON) or disables

ON

TRANSFER]

(OFF) the automatic call

OFF

 

transferring to telephone.

 

[SCHEDULE

Enables or disables the call

ON

TEL TRANSFE]

transferring to telephone to

OFF

(schedule

perform transferring on the

 

telephone

schedule preset by the System

 

transfer)

settings automatically.

 

1 Press repeatedly to select [TRANSFER] (so that it is highlighted), and then press ZOOM/WIDE to select.

The sub items are displayed.

*The sub items can also be displayed by pressing TRANSFER in the standby mode.

NOTE:

The above display example differs from the actual one.

2 Press repeatedly to select the target sub item (so that it is highlighted), and then press ZOOM/WIDE to select.

3 Make the settings on each sub item as follows.

[CALL TRANSFER]:

Press repeatedly to select ON or OFF, and then press ZOOM/WIDE to decide on the selected one.

[TRANSFER DESTINA] (Transfer destination):

*This setting is available only when [CALL TRANSFER] is ON.

Press repeatedly to select the target master station in your site or a remote site (so that it is highlighted), and then press ZOOM/WIDE .

*The LED on TRANSFER lights up (red) when [CALL TRANSFER] is set ON and the target is set at [TRANSFER DESTINA].

[TRANSFER DELAY]:

*This setting is available only when [CALL TRANSFER] is set ON and the target is set at [TRANSFER DESTINA].

Press repeatedly to set the delay time, and then press ZOOM/WIDE to select.

*If the delay time is set to “00”, a call will be transferred to the target directly.

[SCHEDULE TRANSFER]:

Press repeatedly to select ON or OFF, and then press ZOOM/WIDE to decide on the selected one.

[SCHEDULE DESTINA] (Schedule destination):

*This setting is available only when [SCHEDULE TRANSFER] is ON.

Press to select the target master station in your site or a remote site (so that it is highlighted), and then press ZOOM/WIDE .

*Press SETTING as “BACK” function to return to the previous screen.

GETTING STARTED SETTING AND ADJUSTMENT USING THE SYSTEM

APPENDIX

19

Image 19
Contents 834174 B P0811JZ Standard IP SystemContents Viewing video images at Target station Paging Chime paging Calling another station Direct voice call MonitoringGeneral Precautions PrecautionsIntroduction Unit becomes inoperative during power failure Color monitor master station Part NamesDisplay item examples MonitorDisplay examples Standby modeVandal-resistant audio door station flush-mount IS-SS Vandal-resistant door stationTransmit LED red Room sub station IS-RSIS-CCU Outline of OperationsCommunication You cannot monitor or scan-monitor a remote site Electric door strike Door station Room sub station Setting items Master Station Settings and AdjustmentsAdjusting sound volume Tone VOL Adjusting screen brightness BrightnessRoom SUB Call Tone Initial settings Initial SettingBasic setting procedure Setting the call-in tones Door Call ToneSub items are displayed Setting the display modes of the monitor DisplayYou can make the following settings for the display modes Press to select the desired search item so thatCall Transfer Transfer DelaySchedule Transfer Telephone Transfer Privacy ModePRIVACY-2 Call Tone Call tone rings, and the corresponding display appears Receiving a callLights up Answer the call in one of the following ways Communication in the hands-free modeCommunication in the press-to-talk mode When called in from a sub stationPress-to-talk mode Communication by using the handsetWhen two or more calls have arrived IS-MV Hands-free modeWide Zoom Switching Zoom/WideViewing video images at a video door station Pan & TiltPress Adjust again Adjusting imagesPress Adjust when the image is difficult to see To restore the image before adjustmentCommunication transferring When both 1 and 3 are set, 3 takes priorityCall transferring To communicate with the caller While receiving a callName Search →P Received Calls →P Standby modeSearch items Stations by Area →P Placed Calls →PRemote Site →P Search ListName Search →P Stations by Area →P Stations by Type →P Paging Zone →P Chime Zone →PYou cannot select two or more remote sites When searching for MASTER004 Press the dial keys as followsSearching for a station, zone or remote site from the list PressAll the station types are displayed in the list Select Stations by Type from the Search LIST. →PAll the stations in the area are displayed in the list You can select up to 5 stations. →PRemote Site You can select up to 5 stations and/or zones. →P Placed CallsPress to select Placed Calls in the standby mode. →P Press to select Received Calls in the standby mode. →PPage Press OFF or hang up the handset to finish communicating Calling another station direct voice callTo shift to scan-monitoring Viewing video images at the target stationMonitoring Scan-monitoringMaking chime paging automatically Communicating with telephone North America only Other FunctionsIt is also possible to set to stop the current chime paging Other functions combined with connected external devicesRoom sub station Central control unitAvailable Character List Technical PrecautionsSpecifications Vandal-resistant audio door station flash-mount IS-SS Vandal-resistant video door station surface-mount IS-DVVandal-resistant video door station flush-mount IS-DVF IP vandal-resistant video door station flush-mount IS-IPDVFPower supply unit IS-PU-UL, IS-PU-S For US market WarrantyObject area of is the EU For Canada market
Related manuals
Manual 28 pages 11.84 Kb