Aiphone Communication by using the handset, When two or more calls have arrived IS-MV

Page 23

Communication by using the handset

<In the hands-free mode>

1)Lift the handset and you can communicate with the handset.

*You can also communicate in the press-to-talk mode by pressing and holding TALK .

2)When you have finished the communication, put the handset on the hook.

Communication will end.

<In the press-to-talk mode>

You can communicate in the press-to-talk mode by pressing and holding TALK even when you are communicating with the handset.

NOTE:

Communication will end automatically according to the set communication time.

When two or more calls have arrived (IS-MV)

*An IS-IPMV cannot receive two or more calls at a time.

1 Select a call to answer by following the steps 1) and 2) below.

1)Press LIST .

The list of calling sub stations is displayed.

2)Press repeatedly so that the station no. (and/or name) of the sub station you will select is highlighted.

*Calls from other master stations are not displayed in the list.

2 Press TALK , ZOOM/WIDE or lift the handset*1, and you can answer the call.

*When the communication is finished, subsequent incoming calls ring.

*(When you are receiving calls from sub stations):

If you select another sub station while communicating, the current communication is forcibly stopped, and then you can answer the selected station with direct voice call after a beep.

*1: When you are receiving a direct voice call from another master station, lifting the handset will not enable you to communicate with the selected sub station. In that case, press TALK or ZOOM/WIDE with the handset lifted.

About the priority

The order of priority for two or more actions (communication, calling, paging, monitoring, etc.) performed at the same time is as follows depending on the priority setting.

Priority

Setting

Action

1 (high)

[URGENT], [BROADCAST]*2

Communication,

2

[PRIORITY]

calling, paging,

3

[NORMAL]

chime paging.

 

4 (low)

-

Monitoring, scan-

 

 

monitoring

*Earlier call has priority over later call if the priority setting is the same. When the communication path is occupied, it is notified by a sound.

*Communication takes priority over calling.

However, when a call with higher priority comes in, the communication will be forcibly stopped.

*With an IS-MV, you can select the desired one from the list of currently received calls, etc.

*2: [BROADCAST]:

This can be selected only when you perform paging. When [BROADCAST] is selected, you can perform paging while interrupting all the other communications of lower priority. In that case, no receiver can answer you.

NOTE:

When communication is stopped by receiving a higher priority operation, a notice sound rings.

GETTING STARTED SETTING AND ADJUSTMENT USING THE SYSTEM

APPENDIX

23

Image 23
Contents 834174 B P0811JZ Standard IP SystemContents Viewing video images at Target station Paging Chime paging Calling another station Direct voice call MonitoringIntroduction PrecautionsGeneral Precautions Unit becomes inoperative during power failure Color monitor master station Part NamesDisplay item examples MonitorDisplay examples Standby modeVandal-resistant audio door station flush-mount IS-SS Vandal-resistant door stationTransmit LED red Room sub station IS-RSIS-CCU Outline of OperationsCommunication You cannot monitor or scan-monitor a remote site Electric door strike Door station Room sub station Setting items Master Station Settings and AdjustmentsAdjusting sound volume Tone VOL Adjusting screen brightness BrightnessRoom SUB Call Tone Initial settings Initial SettingBasic setting procedure Setting the call-in tones Door Call ToneSub items are displayed Setting the display modes of the monitor DisplayYou can make the following settings for the display modes Press to select the desired search item so thatSchedule Transfer Transfer DelayCall Transfer PRIVACY-2 Call Tone Privacy ModeTelephone Transfer Lights up Receiving a callCall tone rings, and the corresponding display appears Answer the call in one of the following ways Communication in the hands-free modeCommunication in the press-to-talk mode When called in from a sub stationPress-to-talk mode Communication by using the handsetWhen two or more calls have arrived IS-MV Hands-free modeWide Zoom Switching Zoom/WideViewing video images at a video door station Pan & TiltPress Adjust again Adjusting imagesPress Adjust when the image is difficult to see To restore the image before adjustmentCall transferring When both 1 and 3 are set, 3 takes priorityCommunication transferring To communicate with the caller While receiving a callName Search →P Received Calls →P Standby modeSearch items Stations by Area →P Placed Calls →PRemote Site →P Search ListName Search →P Stations by Area →P Stations by Type →P Paging Zone →P Chime Zone →PYou cannot select two or more remote sites When searching for MASTER004 Press the dial keys as followsSearching for a station, zone or remote site from the list PressAll the station types are displayed in the list Select Stations by Type from the Search LIST. →PAll the stations in the area are displayed in the list You can select up to 5 stations. →PRemote Site You can select up to 5 stations and/or zones. →P Placed CallsPress to select Placed Calls in the standby mode. →P Press to select Received Calls in the standby mode. →PPage Press OFF or hang up the handset to finish communicating Calling another station direct voice callTo shift to scan-monitoring Viewing video images at the target stationMonitoring Scan-monitoringMaking chime paging automatically Communicating with telephone North America only Other FunctionsIt is also possible to set to stop the current chime paging Other functions combined with connected external devicesRoom sub station Central control unitAvailable Character List Technical PrecautionsSpecifications Vandal-resistant audio door station flash-mount IS-SS Vandal-resistant video door station surface-mount IS-DVVandal-resistant video door station flush-mount IS-DVF IP vandal-resistant video door station flush-mount IS-IPDVFPower supply unit IS-PU-UL, IS-PU-S Object area of is the EU WarrantyFor US market For Canada market
Related manuals
Manual 28 pages 11.84 Kb