Aiphone IS operation manual Calling another station direct voice call

Page 35

Calling another station (direct voice call)

Follow the steps below to call a desired door station, room sub station, master station in your site, or a remote site.

1 Search for and select the station or remote site you want to call (so that it is highlighted) in one of the search methods. (→P. 28-34)

*If you call (the pilot station in) a remote site by searching for it from [REMOTE SITE] of SEARCH LIST, select the target site, and then select [CALL] (so that it is highlighted). (→P. 32)

Refer to the on-screen instructions:

Be sure to make operations by checking the information on the upper part of the monitor. The next operations you can perform are displayed.

e.g.)

[] TALK … You can start talking by pressing TALK or lifting the handset.

*If you will not set the priority, it is set to “Normal”.

[] MONI … You can start monitoring by pressing

MONITOR .

[ ] PR (or PRIORITY)

………You can proceed to the priority setting mode by pressing ZOOM/WIDE .

2 To set the priority, press ZOOM/WIDE , and then

press to select the target priority (so that it is highlighted).

*If you will not set the priority, skip this step and press TALK or lift the handset. You can start calling (talking).

3 Press TALK or ZOOM/WIDE or lift the handset to start calling (talking).

or

or

When a tone rings, your voice is heard at the target station and you can also hear sounds at the target station. (Direct voice call)

The receiver can answer the call without pressing any button or lifting the handset. (Talk back)

*If the target station is a master station, the response of it differs from the PRIVACY MODE setting on the target station. (See the table below.)

PRIVACY MODE

 

 

 

 

 

setting on the target

 

Response

master station

 

 

 

 

 

 

Your voice is heard at the target

OFF

station and you can also hear sounds

 

at the target station.

 

 

 

 

 

 

 

Communication is enabled when the

1

receiver presses

TALK

or lifts the

handset. Otherwise you can hear no

 

 

sound from the target station.

 

 

 

 

 

 

 

When the target station receives your

 

call, a tone notifies you that the target

 

station is in the (PRIVACY MODE) 2.

 

Communication is enabled when the

2

receiver presses

TALK

or lifts the

handset. Otherwise you can hear no

 

 

sound from the target station.

 

* You can adjust the volume of call

 

tone from [RECEIVE VOL] by

 

pressing

SETTING

.

 

 

 

 

 

 

4 Press OFF or hang up the handset to finish communicating.

GETTING STARTED SETTING AND ADJUSTMENT USING THE SYSTEM

APPENDIX

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents 834174 B P0811JZ Standard IP SystemContents Viewing video images at Target station Paging Chime paging Calling another station Direct voice call MonitoringIntroduction PrecautionsGeneral Precautions Unit becomes inoperative during power failure Color monitor master station Part NamesDisplay item examples MonitorDisplay examples Standby modeVandal-resistant audio door station flush-mount IS-SS Vandal-resistant door stationTransmit LED red Room sub station IS-RSIS-CCU Outline of OperationsCommunication You cannot monitor or scan-monitor a remote site Electric door strike Door station Room sub station Setting items Master Station Settings and AdjustmentsAdjusting sound volume Tone VOL Adjusting screen brightness BrightnessRoom SUB Call Tone Initial settings Initial SettingBasic setting procedure Setting the call-in tones Door Call ToneSub items are displayed Setting the display modes of the monitor DisplayYou can make the following settings for the display modes Press to select the desired search item so thatSchedule Transfer Transfer DelayCall Transfer PRIVACY-2 Call Tone Privacy ModeTelephone Transfer Lights up Receiving a callCall tone rings, and the corresponding display appears Answer the call in one of the following ways Communication in the hands-free modeCommunication in the press-to-talk mode When called in from a sub stationPress-to-talk mode Communication by using the handsetWhen two or more calls have arrived IS-MV Hands-free modeWide Zoom Switching Zoom/WideViewing video images at a video door station Pan & TiltPress Adjust again Adjusting imagesPress Adjust when the image is difficult to see To restore the image before adjustmentCall transferring When both 1 and 3 are set, 3 takes priorityCommunication transferring To communicate with the caller While receiving a callName Search →P Received Calls →P Standby modeSearch items Stations by Area →P Placed Calls →PRemote Site →P Search ListName Search →P Stations by Area →P Stations by Type →P Paging Zone →P Chime Zone →PYou cannot select two or more remote sites When searching for MASTER004 Press the dial keys as followsSearching for a station, zone or remote site from the list PressAll the station types are displayed in the list Select Stations by Type from the Search LIST. →PAll the stations in the area are displayed in the list You can select up to 5 stations. →PRemote Site You can select up to 5 stations and/or zones. →P Placed CallsPress to select Placed Calls in the standby mode. →P Press to select Received Calls in the standby mode. →PPage Press OFF or hang up the handset to finish communicating Calling another station direct voice callTo shift to scan-monitoring Viewing video images at the target stationMonitoring Scan-monitoringMaking chime paging automatically Communicating with telephone North America only Other FunctionsIt is also possible to set to stop the current chime paging Other functions combined with connected external devicesRoom sub station Central control unitAvailable Character List Technical PrecautionsSpecifications Vandal-resistant audio door station flash-mount IS-SS Vandal-resistant video door station surface-mount IS-DVVandal-resistant video door station flush-mount IS-DVF IP vandal-resistant video door station flush-mount IS-IPDVFPower supply unit IS-PU-UL, IS-PU-S Object area of is the EU WarrantyFor US market For Canada market
Related manuals
Manual 28 pages 11.84 Kb
Top Page Image Contents