C. Crane A-66 manual Diagnosis Using a Palm Pilot Set- ting Module, Display Meaning Trouble

Appendix A Optipay™CC TROUBLE SHOOTING

Table A-1 LED Indicator Meanings (Continued)

LED	Meaning	Trouble
Yellow	Coins stuck in	Remove tube cassette
Flashes	vend area or	and any jammed coins,
Twice	motor failure	then vend one coin from
		each tube using the
		inventory keys or Ser-
		vice case
Yellow	Coin changer	Check Vending
Flashes	inhibited	Machine (possibly
3 times	by Vending	empty or defective)
	Machine
Red	Fault in Coin	Remove jammed coins
Flashes	Validator	by pressing the return
once		lever on the Coin Valida-
		tor or Service case, Coin
		Validator may have to be
		exchanged
Red	Fault in Coin	Service case, Coin
Flashes	Validator	Validator may have to be
twice		exchanged
Red	Vending	Check Vending
Flashes	Machine no	Machine control or
3 times	longer com-	connecting cable
	municates
	with Coin
	Changer (has
	sent no com-
	mand in 2
	secs.)

Diagnosis Using a Palm Pilot® Set- ting Module

If a Coin Changer fault occurs, the Palm Pilot® Set- ting Module displays the appropriate status or error message as soon as you connect it to the RJ-45 interface jack on the Coin Changer’s front panel (see chapter 11 "Configuration"). Depending on the operating mode or fault, three status or fault messages are displayed as follows:

•INFO messages: used in general only for information about particular operating states

•AN/AB messages: indicate where a coin was accepted (AN) or why a coin was rejected (AB)

•FE messages: indicate why the Coin Changer no longer functions (Table A-2).

Table A-2 Display Indicators

Display	Meaning	Trouble
INFO	Return Lever	No error or, check the
INFO -01	pressed or a	return mechanism in
	switch in Coin	Vending Machine, or
	Validator defec-	Service case
	tive

Table A-2 Display Indicators (Continued)

Display	Meaning	Trouble
InFo-09	String sensor	Coin on string
	active	recognized (no error),
		or
		check sensor
		(Service case)
InFo-09A	Tube coins are	No error.
	delivered to the	This function can be
	cash-box after	deactivated however,
	a recognized	using PRO 04 02
	string manipu-
	lation
InFo-80	Coin Changer	Check Vending
	inhibited by	Machine (possibly
	Vending	empty or defective)
	Machine
AN	Accepted coin	No error
An X YY
	will be sorted
	into:
	X = 0 cash-box
	X = 1 left tube
	X = 2 middle
	left tube
	X = 3 middle
	right tube
	X = 4 right tube
An X YY	Inserted coins
	accepted in the
	coin channel
	YY = 01–16
	(Channel No.)
AB	Measured	If necessary, widen
Ab-01
	inserted coin	acceptance band limit
	values are out-	using with WinEMP© or
	side the accep-	PalmEMP©
	tance band limit
Ab-02	Inserted coin	Enable coin channel
	inhibited by the	using DIP Switch Block
	Coin Changer	or Palm Setting Module
		with WinEMP© or Palm
		Pilot® with PalmA66©
Ab-03	Inserted coin	Remove coins or for-
	has not passed	eign objects by press-
	through mea-	ing the return lever on
	surement sec-	the Coin Validator, or
	tion in the	check measurement by
	appropriate	air-core coil or CP2
	amount of time	level (Service case)
Ab-04	Inserted coin	Insert coin again more
	was not recog-	slowly
	nized
Ab-05	CP3 or CP4	Insert coin more slowly,
	sensor active	or inserted coin not on
		string or check sensors
		(Service case)

5900335 © 2005 JCM-American Corporation

A - 2