Vertex Standard FTM-10R manual Mobile Installation

Page 14

INSTALLATION

MOBILE INSTALLATION

The FTM-10Rmust only be installed in vehicles having a 13.8 Volt negative ground elec- trical system. Mount the transceiver where the display, controls, and microphone are easily accessible, using the supplied Mobile Mounting Bracket.

The transceiver may be installed in almost any location, but should not be positioned near a heating vent or anywhere where it might interfere with driving (either visually or me- chanically). Make sure to provide plenty of space on all sides of the transceiver so that air can flow freely around the radio’s case.

An antenna and an antenna cable are not included in the box. Purchase them separately to accommodate your transceiver installation.

The DC power cable draws a large current when transmitting. The power cable should be wired as short as possible, and connected directly to the battery. (Do not use the cigarette lighter socket for power connections).

Never remove the fuse holders from the DC cables Never connect the transceiver directly to a 24 V battery.

Select a low-loss coaxial cable to connect the transceiver with the antenna. Use the shortest length possible.

Select a quality, high efficiency VHF/UHF antenna, and mount it in a good location on the car to obtain the maximum performance from the transceiver. (NOTE: An antenna designed with a matching device that forms a low DC resistance to ground may have poor reception on the AM broadcast band.)

The antenna depends on good grounding to realize maximum performance. Contact your dealer for information on transceiver and antenna installation.

If alternator noise exists, use a line filter in the DC power cable connection.

IMPORTANT: Select a location which can support the weight of the FTM-10Rtrans- ceiver and does not interfere with your driving.

12	FTM-10R OPERATING MANUAL

Image 14

Contents FTM-10R Contents Features New Concept in Ultra compact Mobile transceiversReliable and advanced performance Features Front Panel & TOP Panel KeysLED Rear Panel & LCD DC 13.8 V Cable Pigtail w/FuseRear Panel EXT SPK jackAccessories & Options Supplied Accessories Optional Accessories FEP-4Preliminary Inspection InstallationInstallation Tips Safety Information Mobile Installation Mobile Power Connections Mobile SpeakersAC Power Supplies Base Station InstallationAntenna Considerations Assumes 50-Ohm Input/Output TerminationsSeparate Installation Installation Front Panel Installation Installation Bracket Rubber NON-SEPARATE Installation Basic Operation ReceiveTransmission Smart Menu Features Display FunctionAF Dual Function Artstm Dimmer Function Dimmer 1 ÅÆ Dimmer 2 ÅÆ Dimmer 3 ÅÆMonitor Feature Intercom FunctionPublic Address Feature Reverse FeatureSmart Searchtm Operation Scan FeatureStoring Smart Search Memories Squelch Level Adjust TX Power Select Intercom Volume ControlMemory Operation Memory StorageAll Memory Channel Recall Group Memory Mode Memory RecallMemory Channel Customization Diaplay FunctionTo eliminate the memory channel from the Group Memory bank Memory Group BankMemory Channel Number Change Memory Channel SortLabeling Memory SKIP/PREFERENTIAL Scan Setting Scan TypeSquelch Level Ctcss FrequencyDCS Code Storing Independent Transmit Frequency ODD Split Using the Standard Repeater ShiftUsing the Odd Split Memory Transmitter Power Level Deleting MemoryActivating the Club Channel Monitor Club Channel OperationRecalling the Club Channel Club Channel Operation Message Feature Programming a MessageProgramming a Member List Cloning Preparations Source TransceiverPreparations Destination Transceiver Cloning the MessageSending a Messages To send a messageSET Your Personal ID Receiving a Message CloningCopy/clone procedure is completed Changing the Club Channel Frequency CLOCK/TIMER Operation SET UP the ClockDisplays the Current Time Activate the ClockDisplay the Clock Using the Stop Watch Timer Using the Interval TimerAutomatic Audio Volume Controller Convenience FeaturesMute Feature AF-VFO Feature VOX OperationListening the AM/FM Broadcast Station TIME-OUT Timer TOTVOX Sensitivity Listening to External Audio Input FTM-10RBluetooth Operation PairingTo activate Bluetooth About the Bluetooth Battery IndicatorAF Dual Function AF Dual Function Ctcss Operation DCS Operation Storing the Ctcss Tone Pairs for Epcs Operation Epcsenhanced Paging & Code Squelch OperationActivating the Epcs Internet Connection Feature Wirestm SRG Sister Radio Group ModeFRG FRIENDS’ Radio Group Mode Programming the FRG codeTo accessing an FRG Node Dtmf Autodialer To load the DTMFAutodialer memoriesTo transmit the memorized telephone number Repeater Operation Standard Repeater ShiftBand Expansion Repeater OPERATION/BAND ExpansionAutomatic Repeater Shift Weather Broadcast Channel Operation Severe Weather AlertChannel Step Selection Miscellaneous SettingChanging the Operating Mode Smart KEY Select PTT KEY FunctionKEY Beeper Automatic Repeater Shift Repeater Shift DirectionRepeater Shift Offset Programming the KEY Assignments SCAN-RESUME Mode Scanning BandScan Direction Scan Start DirectionCTCSS/DCS/EPCS Bell Operation Split Tone OperationClock Format Battery Voltage DisplayTemperature Display Interval Beep Alarm SETTime System Automatic POWER-OFF APO Audio Pitch ControlVolume Setting Alert Feature Speaker SelectionMIC Gain Setting STEREO/MONAURAL SelectionMenu SET Mode Default Bold ItaricMenu Item Function Available Values Default Bold Itaric ENU ODECTCSS/DCS/DTMF Setting ODE ENUAmateur Bands SQL Set Mode Item F2 AF Dual Set Mode Item F1 AF AutoDefault OFF Set Mode Item F5 AF-VFO Set Mode Item F3 AF PitchSet Mode Item F4 AF Prest Set Mode Item F6 BeepSet Mode Item F9 Clock Set Mode Item F8 BLU VOXDefault PTT Available Values OFF/AUTO/HOLD Default OFFSet Mode Item F17 ID REG Set Mode Item F15 Fkey SELDefault PA Set Mode Item F16 ID List Set Mode Item F18 MessageSet Mode Item F27 RX EXP Set Mode Item F24 RPT ARSSet Mode Item F26 RPT SFT Set Mode Item F28 RX F CCLSet Mode Item F33 SCN Strt Set Mode Item F32 SCN ModeDefault Busy Set Mode Item F37 SQL EXP Set Mode Item F35 SQL BellDefault OFF Set Mode Item F36 SQL DCS Set Mode Item F41 Step Set Mode Item F39 SQL TsqfSet Mode Item F40 SQL Type Set Mode Item F42 StereoSet Mode Item F47 VOX Sens Set Mode Item F45 VOL.ITCOMSet Mode Item F46 VOX MIC Default Set Mode Item F48 WiresReset Procedure Troubleshooting Specifications Squelch Sensitivity Circuit TypeSensitivity SelectivityDeclaration by Manufacturer 0704z-0E