Lincoln Electric SVM149-A service manual Pro-Cut

Page 1

TOC

Info

RETURN TO MAIN MENU

SVM149-A

October, 2006

Return to Master

Return to Master TOC

Return to Master TOC

Return to Master TOC

View Safety

View Safety Info

View Safety Info

View Safety Info

PRO-CUT 25

For use with machine code numbers 10661

Safety Depends on You

Lincoln arc welding and cutting equipment is designed and built with safety in mind. However, your overall safety can be increased by proper installation

. . . and thoughtful operation on your part. DO NOT INSTALL,

OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READ- ING THIS MANUAL AND THE SAFETY PRECAUTIONS CON- TAINED THROUGHOUT. And, most importantly, think before you act and be careful.

SERVICE MANUAL

Copyright © 2006 Lincoln Global Inc.

• World's Leader in Welding and Cutting Products •

• Sales and Service through Subsidiaries and Distributors Worldwide •

Cleveland, Ohio 44117-1199 U.S.A. TEL: 1-888-935-3877 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com

Image 1

Contents PRO-CUT Safety Cylinder may explode if damaged Précautions DE Sûreté SafetyMaster Table of Contents for ALL Sections PRO-CUT Installation Section Table of ContentsTechnical Specifications PRO-CUT 25 K1756-1 InstallationSelect Proper Location Safety Precautions Electric Shock can KillHigh Frequency Interference Protection Input Electrical ConnectionsGAS Input Connections Torch Output ConnectionsPRO-CUT Table of Contents Operation Section Preheat Temperature for Plasma Cutting Safety PrecautionsOperation DescriptionDesign Features Advantages Operational Features and ControlsUser Responsibility Consumable Life Cutting CapabilityLimitations Controls and SettingsPilot ARC Discussion Apparently wrong, reset the machine by turningGeneral In All Cases Procedure RecommendationsPRO-CUT Accessories General Options Accessories Maintenance Electric Shock can kill Routine MaintenancePRO CUT PRO-CUT Table of Contents Theory of Operation Section General Description Theory of OperationInput Line VOLTAGE, and Auxiliary Transformer Figure E.3 Precharge and Protection Precharge and ProtectionReturn Return to Section TOC Main TransformerFigure E.5 Plasma Output Section and Torch Figure E.6 Control Board Control BoardProtection Circuits Safety PARTS-IN-PLACE ProtectionAccidental Operation Protection Insulated Gate Bipolar Transistor Igbt Operation Table of Contents Troubleshooting & Repair Section HOW to USE Troubleshooting Guide Troubleshooting & RepairPC Board Troubleshooting Procedures Output Problems Function Problems See the Operation section Troubleshooting & Repair LED Function Problems Description Input Filter Capacitor Discharge ProcedureRight Side of Machine Discharge ProcedureMain Inverter Board Resistance Test Right Side of Machine IGBT’s D2 D1 D11 D10 PRO-CUT Input Board Voltage Test Test Points Fan PRO-CUT Main Inverter Board Voltage Test P2 P1 P2 P1 PRO-CUT Torch Continuity and Solenoid Test Torch Continuity and Solenoid Test Torch Continuity and Solenoid Test PRO-CUT AIR/GAS Solenoid Test AIR/GAS Solenoid Test Control Board Removal and Replacement Small Red Cap Screws Over tighten Input Board Removal and Replacement Input Board Input Board Removal & Replacement PRO-CUT Main Inverter Board Removal and Replacement Main Board Main Inverter Board Removal & Replacement PRO-CUT Switch Removal and Replacement PRO FAN Removal and Replacement Fan Do Not Over tighten Machine Input and Output Retest After RepairTable of Contents Electrical Diagrams Section Electrical DiagramsInput Voltage Board Pressure SCHEMATIC- Control Printed Circuit Board Sheet Electrical Diagrams Electrical Diagrams PC Board Assembly Main Inverter Board PC Board Assembly Input Board Cutting Current Path SVM Error Reporting Form