Lincoln Electric LN-10 manual Explanation of Prompting and Error Messages, Display Prompt or Error

Page 26

B-13

OPERATION

B-13

 

 

 

EXPLANATION OF PROMPTING AND ERROR MESSAGES

Display

Prompt or Error

Acc

Displayed on Voltage display, indicates WFS

 

display is showing acceleration setting, “1" to

 

“5" (See “Acceleration Selection” in this sec-

 

tion).

OFF

Displayed on WFS and voltage displays; indi-

 

cates limits for WFS or voltage are off for the

 

displayed procedure. (See “Maximum and

 

Minimum Limits Setting Modes” in this sec-

 

tion).

SEC

Displayed on WFS display, indicates Voltage

 

display is showing a Timer setting in sec-

 

onds. (See “Display Control Keys” in this

 

section)

GLP

Displayed on WFS display, indicates that the

 

Grounding Lead Protector circuit was activat-

 

ed due to excessive current flow into the

 

wire feeder frame. When the GLP circuit is

 

activated the wire feeder is disabled (the trig-

 

ger output to the power source is opened up,

 

the motor is stopped, and the gas solenoid is

 

turned off). To resume normal operation,

 

release the trigger, make sure that the elec-

 

trode is not touching the wire feeder frame,

 

and then either press a key on the keypad or

 

close the trigger. (See “Grounding Lead

 

Protector” in this section)

Cld

Displayed on Voltage display when Cold

 

Feed Forward or Cold Feed Reverse Key is

 

pressed, or Cold Feed Trigger mode is

 

selected. Indicates wire is fed “cold” (no

 

weld voltage) at the speed indicated on the

 

WFS display. (See “Operation Keys” and

 

“Trigger Mode Selection” in this section).

---Displayed on Voltage or WFS displays with RUN-IN selected, indicates setting will match those set for Weld Voltage and Wire Feed Speed (See “Display Control Keys” in this section).

HXX

Displayed on WFS display, indicates wire feed over-

 

load. XX indicates time remaining in seconds before

 

unit resets automatically. (See “Wire Feed Overload

 

Protection” in this section and “Avoiding Wire

 

Feeding Problems” in the MAINTENANCE section).

Er

EEPROM error. Usually occurs at power-up.

 

Indicates one or more of the recalled settings is out

 

of acceptable limits. Press any key to return to nor-

 

mal operation. Be sure to check all voltage, wire feed

 

speed, acceleration and timer settings before you

 

proceed.

LN-10

Page 25 Page 27
Image 26
Page 25 Page 27
Contents IM906 Safety California Proposition 65 WarningsElectric Shock can kill Welding and Cutting Sparks can Cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a LʼArcPlease Examine Carton and Equipment For Damage Immediately On-Line Product RegistrationTable of Contents Recommended Processes and Equipment InstallationGeneral Description Available ModelsSeries Wire Drive Ratio Selection Wire Drive Speed Range SelectionControl Speed Range Setting Electrode RoutingGUN and Cable Assemblies with Standard Connection Wire Feed Drive Roll KitsProcedure to Install Drive Roll and Wire Guides Gun Cable Connection with Standard Connection Series Wire Drive Water Connections for Water Cooled GunsGUN and Cable Assemblies with FAST-MATE Connection Gun Cable Connection with Fast-Mate ConnectionGmaw Shielding Gas Electrical InstallationInput Cable LN-10 Control to Power Source Optional Features Installation Dual Procedure Switch OptionsOperation LN-10 Control DIP Switch SetupSetup DIP Switch Access Welding Power Source Selection Setting the DIP SwitchesWire Drive Head Selection Metric/English Wire Feed Speed Display Selection Step Trigger Mode Operation SelectionMaximum Limits Setting Mode Selection Security Mode SelectionRobotics Mode Selection Minimum Limits Setting Mode SelectionKeypad and Display Description Power-Down SaveKeypad and Display Operation Operation KeysDisplay Control Keys Trigger Mode SelectionTrigger Mode Select Key Acceleration Selection Security ModeControl Select key enables operator to Digital Memory VoltmeterMaximum and Minimum Limits Setting Modes Dual Procedure Remote Control K1449-1 Wire Reel Loading READI-REELS, Spools or CoilsFeeding Electrode and Brake Adjustment Drive Roll Pressure SettingMaking a Weld Procedure for Setting Angle of FeedplateGAS Guard Regulator Setting Grounding Lead Protector Wire Reel ChangingWire Feed Overload Protection Explanation of Prompting and Error Messages Display Prompt or ErrorAccessories K683-1 Dual Procedure Switch K683-3 Dual Procedure SwitchK1449-1 Dual Procedure Remote Control GUN Adapters for 10 Series Wire DriveGUN and Cable Assemblies K1557-1 Swivel Mount K1558-1 Remote Switch Interface ModuleK1634-3 Wire Reel Enclosure KIT K1556-1 Light Duty Caster KITGun and Cable Maintenance MaintenanceWire Drive Motor and Gearbox Drive Rolls and Guide TubesTroubleshooting HOW to USE Troubleshooting GuideAuthorized Field Service Facility Contact your local LincolnProblems Symptoms Recommended Course of Action Contact your local Lincoln Authorized Field Service Facility Troubleshooting Problems Possible Recommended Troubleshooting Voltage DIP switch S1 is incorrectly set for Procedure for Replacing PC Boards Electric Shock can killDiagrams 10-STT/ Wire DRI VE Dimension Print 18903LN-10 LN-10 Precaucion Warnung
Top Page Image Contents