Lincoln Electric IM586-B manual Security Mode, Acceleration Selection

Page 22

B-5

OPERATION

B-5

 

 

 

RANGE Range Select key - enables operator to choose which weld parameter to set the maxi- mum or minimum range. Pressing the key causes the range mode lights to sequence (top to bottom) starting from the current indicated selection. The range settings can be set inde- pendently for each procedure.

Security Mode

Security mode is provided to capture and prevent changing of procedure settings. Security mode is activated, or deactivated by setting S1 DIP switch located inside the STT-10 Control Box.

Security mode is used to capture control, acceleration, and range selections and settings, then to disable these selections

PEAK MAX

PEAK MIN

BACKGROUND MAX

BACKGROUND MIN

WFS MAX

WFS MIN

Top Light - PEAK MAX - Indicates that the maximum peak current setting is being dis- played on the top LED display. This para- meter is settable from 17 to 464 amps.

Second Light - PEAK MIN - Indicates that the minimum peak current setting is being displayed on the top LED display. This parameter is settable from 17 to 464 amps.

until security mode is deactivated. Encoder knob setting changes of cold feed, weld speed, peak current, and back- ground current are not disabled.

Security mode is activated, or deactivated, by shutting off the input power to the STT-10 with all Range and Control settings as desired for both procedures. Then setting S1 DIP switch 6 inside the STT-10 Control Box ON or OFF and restoring input power (See “Security Mode Selection” in this section).

Third Light - BACKGROUND MAX - Indicates that the maximum background current setting is being displayed on the top LED display. This parameter is settable from 6 to 153 amps.

Fourth Light - BACKGROUND MIN - Indicates that the minimum background current setting is being displayed on the top LED display. This parameter is settable from 6 to 153 amps.

Fifth Light - WFS MAX - Indicates that the maximum wire feed setting is being displayed on the bottom LED display. This para- meter is settable for the entire wire feed speed range of the cur- rent wire feed head.

Bottom Light - WFS MIN - Indicates that the minimum wire feed setting is being displayed on the bottom LED display. This para- meter is settable for the entire wire feed speed range of the cur- rent wire feed head.

Acceleration Selection

To provide optimum starting of various processes and proce- dures, the wire feed acceleration of the STT-10 can be set to five levels; 1 thru 5, for each procedure. 1 is the slowest accel- eration and 5 is the fastest. (Factory set to 4.)

When activated, the Range and Control selections no longer light, but function with the captured settings. All other keys and encoder knob controls function normally.

GAS PURGE

RANGE

To change acceleration hold the Gas Purge Key closed, then press the Range key. The top display shows “Acc” indicating acceleration set- ting, 1 thru 5, is displayed on the bottom (Speed) display. Use the speed encoder knob to change setting from 1 thru 5.

To exit this function, and enter the acceleration setting into the procedure memory, press both keys again or close the trigger.

STT-10

Image 22
Contents IM586-B Safety California Proposition 65 WarningsElectric Shock can kill Welding and Cutting Sparks can Cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a LʼArcPlease Examine Carton and Equipment For Damage Immediately On-Line Product RegistrationTable of Contents Vii Diagrams Section FP312 Series General Description InstallationSTT-10 Mounting the 10 Series Wire Drive Unit Safety PrecautionsRecommended Processes and Equipment Connecting Wire Drive Unit to Control Box Mounting Synergic 7F Wire Drive UnitMounting the STT-10 Control Box K1565-2 Boom Model Series Wire Drive Ratio Selection Wire Drive Speed Range SelectionControl Speed Range Setting Electrode RoutingSynergic 7F 4-Roll Kits KP655 and KP656 Wire Feed Drive Roll KitsProcedure to Install Drive Roll and Wire Guides Electric Shock can killGUN and Cable Assemblies with FAST-MATE Connection GUN Connections GeneralGUN and Cable Assemblies with Standard Connection Gmaw GunsGun Cable Connection with Fast-Mate Connection Synergic 7F Wire Drives K679Water Connections for Water Cooled Guns Gmaw Shielding GasElectrical Installation Input Cable STT-10 Control to Power SourceBoom and Bench Conversions Optional Features InstallationDual Procedure Switch Options Materials Required for bench to boom conversionOperation STT-10 Control DIP Switch SetupOperating Instructions Robotics Mode Selection Step Trigger Mode Operation SelectionSecurity Mode Selection Range Lockout Mode SelectionOperation Keys Power-Down SaveKeypad and Display Operation Keypad and Display DescriptionTrigger Mode Select Key Trigger Mode SelectionDisplay Control Keys Security Mode Acceleration SelectionWire Reel Loading READI-REELS, Spools or Coils Figure B.1Feeding Electrode and Brake Adjustment Drive Roll Pressure SettingGAS Guard Regulator Setting Procedure for Setting Angle of FeedplateMaking a Weld Explanation of Prompting and Error Messages Wire Reel ChangingWire Feed Overload Protection Display Prompt or ErrorRoll DH Drive AccessoriesSolid & Cored Steel Electrode Driven K1558-1 Remote Switch Interface Module K683-1 Dual Procedure SwitchK683-3 Dual Procedure Switch K1758-L Input Cable Assem BLYMagnum 200/300/400 Guns GUN Adapters for 10 Series Wire Drive HeadsCoil Adapter K206, K289, and K309K1634-1 Wire Reel Enclosure KIT GUN and Cable AssembliesMaintenance MaintenanceTroubleshooting HOW to USE Troubleshooting GuideContact your local Lincoln Authorized Field Service Facility Authorized Field Service Facility Contact your local LincolnTroubleshooting Damaged encoder p.c. board Troubleshooting Procedure for Replacing PC Boards Electric Shock can killDiagrams Diagrams Diagrams Connection Diagrams Dimension Print Bench Model Dimension Print Boom Model Control Box STT-10 STT-10 Precaucion Warnung