Lincoln Electric IM586-B manual GUN Connections General, Gmaw Guns

Page 14

A-6

INSTALLATION

A-6

 

 

 

6)Install each drive roll by pushing over shaft until it butts up against locating shoulder on the drive roll shaft. (Do Not exceed maximum wire size rating of the wire drive).

7)Install Outer Wire Guide by sliding over locating pins and tightening in place.

8)Engage upper drive rolls if they are in the “open” position and close Pressure Door.

TO SET IDLE ROLL PRESSURE, see “Idle Roll Pressure Setting” in OPERATION.

GUN CONNECTIONS - GENERAL

4-roll feed plates are equipped with a brass connector bar at the gun-end of the feed plate to allow a bolted brass-to-brass electrical connection to be made direct- ly to either standard or Fast-mate gun adapter bush- ings. Use a 1/4” inch allen key on the factory-installed socket head cap screw to insure that the connector bar is securely tightened to the adapter bushing.

GUN AND CABLE ASSEMBLIES WITH STANDARD CONNECTION

The 10 Series Wire Drive Head requires a K1500 Gun Adapter installed See “Gun Adapters” in ACCES- SORIES section. The K1500-2 Gun Adapter and Trigger Cable for Magnum 200-400 guns are factory included with the STT-10.

GMAW Guns

An expanding line of Magnum gun and cable assem- blies are available to allow welding with solid and cored electrodes using the GMAW process. See the appropriate Magnum literature for descriptions of the 200 to 550 ampere air cooled gun and cables that are available. Gun cable lengths range from 10 ft. (3.0 m) to 25 ft. (7.6 m) and feed electrode sizes .025" (0.6

mm)to 3/32" (2.4 mm). The entire line of Magnum Fast-Mate gun and cable assemblies can also be used by installing a K489-2 Fast-Mate adapter kit. See “Gun and Cable Assemblies with Fast-Mate Connection” in this section for details.

Gun Cable Connection with Standard Connection

1.Check that the drive rolls and guide tubes are proper for the electrode size and type being used. If necessary, change them per “Wire Drive Roll Kits” in this section.

2.Lay the cable out straight. Insert the connector on the welding conductor cable into the brass conduc- tor block on the front of the wire drive head. Make sure it is all the way in and tighten the hand clamp. Keep this connection clean and bright. Connect the trigger control cable polarized plug into the mating 5 cavity receptacle on the front of the wire drive unit.

3.For GMA Gun Cables with separate gas fitting (10 Series Wire Drive using K1500-1 Gun Adapter), connect the 3/16" I.D. gas hose from the wire drive unit to the gun cable barbed fitting.

GUN AND CABLE ASSEMBLIES WITH FAST-MATE CONNECTION

(Requires K489-2 Fast Mate™ Adapter Kit used with the K1500-1 Gun Adapter)

GMAW Guns

An expanding line of Magnum Fast-Mate™ air cooled and water cooled gun and cable assemblies are avail- able to allow welding with solid and cored electrodes using the GMAW process. See the appropriate Magnum literature for descriptions of the 200 to 400 ampere air cooled gun and cables that are available as well as the Magnum “Super Cool” 450 ampere water cooled gun and cable. Gun cable lengths range from 10 ft. (3.0 m) to 25 ft. (7.6 m) and feed electrode sizes .025" (0.6 mm) to 5/64" (20 mm).

An expanding line of Magnum X-Tractor gun and cable assemblies provides fume extraction capability for welding with solid and cored electrodes using the GMAW process. See the appropriate Magnum litera- ture for descriptions of the 250 to 400 ampere air cooled gun and cables that are available. Gun cable lengths range from 10 ft. (3.0 m) to 15 ft. (4.5 m) and feed electrode sizes .035" (0.9 mm) to 1/16" (1.6 mm). These guns require the use of either the K173-1 or K184* vacuum units.

*Requires S14927-8 connector hose and an S20591 hose adapter.

STT-10

Image 14
Contents IM586-B Safety California Proposition 65 WarningsElectric Shock can kill Welding and Cutting Sparks can Cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a LʼArcPlease Examine Carton and Equipment For Damage Immediately On-Line Product RegistrationTable of Contents P312 Series Diagrams Section FVii STT-10 InstallationGeneral Description Recommended Processes and Equipment Safety PrecautionsMounting the 10 Series Wire Drive Unit Mounting the STT-10 Control Box K1565-2 Boom Model Mounting Synergic 7F Wire Drive UnitConnecting Wire Drive Unit to Control Box Series Wire Drive Ratio Selection Wire Drive Speed Range SelectionControl Speed Range Setting Electrode RoutingSynergic 7F 4-Roll Kits KP655 and KP656 Wire Feed Drive Roll KitsProcedure to Install Drive Roll and Wire Guides Electric Shock can killGUN and Cable Assemblies with FAST-MATE Connection GUN Connections GeneralGUN and Cable Assemblies with Standard Connection Gmaw GunsGun Cable Connection with Fast-Mate Connection Synergic 7F Wire Drives K679Water Connections for Water Cooled Guns Gmaw Shielding GasElectrical Installation Input Cable STT-10 Control to Power SourceBoom and Bench Conversions Optional Features InstallationDual Procedure Switch Options Materials Required for bench to boom conversionOperating Instructions STT-10 Control DIP Switch SetupOperation Robotics Mode Selection Step Trigger Mode Operation SelectionSecurity Mode Selection Range Lockout Mode SelectionOperation Keys Power-Down SaveKeypad and Display Operation Keypad and Display DescriptionDisplay Control Keys Trigger Mode SelectionTrigger Mode Select Key Security Mode Acceleration SelectionWire Reel Loading READI-REELS, Spools or Coils Figure B.1Feeding Electrode and Brake Adjustment Drive Roll Pressure SettingMaking a Weld Procedure for Setting Angle of FeedplateGAS Guard Regulator Setting Explanation of Prompting and Error Messages Wire Reel ChangingWire Feed Overload Protection Display Prompt or ErrorSolid & Cored Steel Electrode Driven AccessoriesRoll DH Drive K1558-1 Remote Switch Interface Module K683-1 Dual Procedure SwitchK683-3 Dual Procedure Switch K1758-L Input Cable Assem BLYMagnum 200/300/400 Guns GUN Adapters for 10 Series Wire Drive HeadsCoil Adapter K206, K289, and K309K1634-1 Wire Reel Enclosure KIT GUN and Cable AssembliesMaintenance MaintenanceTroubleshooting HOW to USE Troubleshooting GuideContact your local Lincoln Authorized Field Service Facility Authorized Field Service Facility Contact your local LincolnTroubleshooting Damaged encoder p.c. board Troubleshooting Procedure for Replacing PC Boards Electric Shock can killDiagrams Diagrams Diagrams Connection Diagrams Dimension Print Bench Model Dimension Print Boom Model Control Box STT-10 STT-10 Precaucion Warnung