Craftsman 921.16474, 921.16475 Pulley Alignment, Replacing or Cleaning the Check Valve, Risk

Page 10

PULLEY ALIGNMENT

,_IL_RISKOF INJURY. This unit starts automatically. ALWAYS shut off the compressor, remove the plug from the outlet, and bleed all pressure from the system before servicing the compressor, and when the compressor is not in use. Do not use the unit with the shrouds or belt guard removed. Serious injury could occur from contact with moving parts.

Motor

Compressor may yaw from one shown

Motor

bolts

To check pulley alignment, remove the belt guard and place a straightedge (see A) against the pump flywheel (see B) (See Fig. 9). Measure and record the distance from the straightedge to the edge of the drive belt at point C. Then measure the distance from the straightedge to the edge of the drive belt again at points D and E. Both distances should be the same as at point C. If D or E are different from C, there is a misalignment which must be corrected before the compressor is run. To correct a pulley misalignment, use the following procedure.

1.Remove the belt guard.

2.Loosen the motor mounting bolts.

3.Loosen the setscrew on the motor pulley.

4.Align the motor pulley with the pump flywheel (C-D-E must be equal ).

5.Retighten the motor pulley setscrew.

6.Adjust the proper belt tension.

7.Retighten the motor mounting bolts.

8.Reinstall the belt guard. All moving parts must be guarded.

Motor'

C

REPLACING OR CLEANING THE CHECK VALVE

__RISK

 

OF INJURY. This unit starts

automatically.

ALWAYS shut off the compressor,

remove

the plug from the outlet, and bleed

all

pressure

from

the system before servicing

the

compressor, and when the compressor is not in use. Do not use the unit with the shrouds or belt guard removed. Serious injury could occur from contact with moving parts.

1.Turn air compressor off, remove the power cord from the outlet or lock out the power supply and relieve all the air pressure from the tank. Make sure the compressor has cooled down before servicing.

2.Loosen the compression nut fitting on the check valve and

pump head using an adjustable wrench. Remove the transfer tube.

3.Loosen the compression nut fitting on the side of the check valve and pressure switch using an adjustable wrench. Remove the bleeder tube.

4.Making note of the orientation for reassembly, unscrew the check valve from the tank (counterclockwise) using a 7/8" open end wrench.

5.Using a pencil or screwdriver, carefully push the valve disc up and down. If the valve disc does not move freely up and down, the check valve needs to be cleaned or replaced.

6.Clean the check valve with warm soapy water and make sure to dry thoroughly before reinstalling. If the disc valve still does not move freely up and down, it will need to be replaced.

7.Apply thread sealant to the check valve threads and reinstall into the tank by turning clockwise. Make sure it is the same orientation as when it was removed.

8.Replace the bleeder tube and tighten compression nuts.

9.Replace the transfer tube and tighten compression nuts.

10.Perform the "Break-in of the pump" procedure in the operating instructions to make sure there are no leaks and it'sworking properly.

Open position

Screwdriver

ot

penc_i

C_oselposition

10

200-2792

Page 9 Page 11
Image 10
Page 9 Page 11
Contents AIR Compressor Operating Instructions Craftsman ONE Year Full WarrantyMaintenance Running TankRisk of Injury Risk of Fire or Explosion Risk of BurstingRisk of Electrical Shock Risk of BurnsCFM Risk to HearingPSI Basic AIR Compressor Assembling the CompressorComponents Motor Reset Switch Extension Cords Electrical WiringGrounding Instructions Daily START-UP Propel debris that may cause eye injury. Wear safetyGoggles when Opening petcock ShutdownDraining the Tank MaintenanceAdjusting Drive Belt Tension Checking the OILRisk Replacing or Cleaning the Check ValvePulley Alignment INJURY. This unit startsChecking the Relief Valve Cleaning the AIR FilterTesting for Leaks StorageProblem Possible Cause Solution Vertical tank 27 Gal El tanque vertical R6servoir vertical Asme13F 200-2792 Article No / P Qty Articulo Num / PDescription Descripcion Io.I Available Service Kits Cuadro DE Deteccion DE Fallos Intervalos DE ServicioEsquema DE LA Piezas Lista DE LAS Piezas Riesgo DE Explosion Bar Riesgo AL Sentido DEL OiDONota Cableado Electrico Presion de conexionComponentesbasicos DEL Compresor DE Aire MontajeInterruptor DE Restablecimiento DEL Motor Instrucciones DE CONEXlON a Tierra Cordones ProlongadoresCableado EL#CTRICO Para Modelos Conectados CON CordonArranque Diario ParadaAbierto Cambio DE Aceite MantenimientoDesagoe DEL Tanque Tension DE LA Correa Y Alineacion DE LA PoleaLlLEsta Alineacion DE LA PoleaSubstituyendo O Limpiando LA Valvula DE Cheque Almacenamiento Limpieza DEL Filtro DE AireDeteccion DE Fugas Revision DE LA Valvula DE AlivioCausa Posible ProblemaSolucion Pression Pression DE Artisan UNE Pleine Garantie DAN PendantMODleLE Sections Pression douverture Risque Auditif Remarque CablageIlectique Pression darret=LleMENTSDE Base DU Compresseur Dair Assemblage DU CompresseurInterrupteur DE Remise EN Marche DU Moteur Instructions DE Mise .&.LA Terre Cablage IlectiqueRallonges Pour Modiles .& CordonOFF C Auto Mise EN Marche QuotidienneARR#T Ouvert FERN# ETension DE LA Courroie ET Aligneimient DE LA Poulie EntretienVidange DU Reservoir Riglage DE LA Tension DE LAAlignement DE LA Poulie Essai Ditanchiiti Remplaant OU Nettoyant LE Clapet AntiRetour EntreposageProbleme Cause Possible Solution Your Home Wsear&com
Top Page Image Contents