Skil 5850 manual Assembly, Attaching the Blade, VARI-TORQUE Clutch, Dust Extraction

Page 9

Assembly

ATTACHING THE BLADE

!WARNING Disconnect battery pack from tool or place the

switch in the locked or off position before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally.

1.Turn BLADE STUD with wrench provided counter-clockwise and remove BLADE STUD and OUTER WASHER (Fig. 2). If the shaft moves while attempting to loosen the blade stud, strike the wrench counter-clockwise to jar BLADE STUD loose.

2.Retract the lower guard all the way up into the upper guard. While retracting the lower guard, check operation and condition of the

LOWER GUARD SPRING.

3.Make sure the saw teeth and arrow on the blade point in the same direction as the arrow on the lower guard.

4.Slide blade through slot in the foot and mount it against the INNER WASHER on the shaft. Be sure the large diameter of the OUTER washer lays flush against the blade.

5.Reinstall OUTER WASHER and tighten BLADE STUD finger tight. To lock shaft hold the saw securely by the upper guard with blade teeth imbedded in scrap wood and TIGHTEN BLADE STUD 1/8 TURN (45°) WITH THE WRENCH PROVIDED.

Do not use wrenches with longer handles, since it may lead to over tightening of the blade stud.

VARI-TORQUE CLUTCH

This clutching action is provided by the friction of the OUTER WASHER against the BLADE and permits the blade shaft to turn when the blade encounters excessive resistance. When the BLADE STUD is properly tightened (as described in No. 5 of Attaching The Blade), the blade will slip when it encounters excessive resistance, thus reducing saw’s tendency to

KICKBACK.

One setting may not be sufficient for cutting all materials. If excessive blade slippage occurs, tighten the blade stud a fraction of a turn more (less than 1/8 turn). OVERTIGHTENING THE BLADE STUD NULLIFIES THE EFFECTIVE- NESS OF THE CLUTCH.

DUST EXTRACTION

(Not included,available as accessory)

Your tool is equipped with a dust port adapter for dust and chip extraction. To attach, push tabs on end of adapter into dust port until it snaps into place. To use this feature, attach standard 1-1/4" vacuum hose (optional accessory) to the dust port adapter.

!WARNING To prevent personal injury, always position dust port

adapter and vacuum hose so that it does not interfere with the lower guard, or the cutting operation at all settings.

DUST PORT ADAPTER

DUST

LOWER GUARD

(Not included,

PORT

SPRING

available as accessory)

 

 

 

 

BLADE SHAFT

LOWER GUARD

 

 

LIFT LEVER

 

 

OUTER WASHER

 

 

Large Diameter

 

FIG. 2

Faces Blade

 

 

Tighten

 

 

 

INNER WASHER

LOWER

 

Large Diameter

GUARD

BLADE

Faces Blade

 

Loosen

 

STUD

BLADE

 

-9-

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Read Before Using Lire avant usage Leer antes de usar Electrical Safety General Safety Rules For All Battery Operated ToolsPersonal Safety Work AreaSafety Rules for Circular Saws ServiceInjury when used on another tool Causes and Operator Prevention Kickback Battery/Charger Battery Disposal Battery CareNails, screws, keys, etc. Fire or injury may result Do not attempt toSymbols Cordless Circular Saw Functional Description and SpecificationsNot included,available as accessory AssemblyAttaching the Blade VARI-TORQUE ClutchDepth Adjustment Safety SwitchOperating Instructions Switch Adjustable Line GuideGeneral Cuts Free movement of the lower guardCutting Large Sheets Pocket CutsRIP Cuts RIP Board GuideBattery Charged Condition Indicator Releasing and Inserting Battery PackCharging Battery Pack Fast Charger Important Charging Notes Mounting Charger to Vertical Surface Mounting ChargerMaintenance AccessoriesCleaning Sécurité électrique Aire de travailUtilisation et entretien des outils Sécurité des personnesRéparation Consignes de sécurité pour scies circulairesDU Rebond Le plomb provenant des peintures à base de plomb Chargeur de pileMise au rebut des piles Entretien des pilesNe tentez pas de Piles NICKEL-CADMIUMSymboles Scie circulaire sans fil Description fonctionnelle et spécificationsMontage DE LA Lame AssemblageEmbrayage « VARI-TORQUE » Extraction DE PoussièreRéglage DE LA Profondeur DE Coupe Consignes de fonctionnementInterrupteur DE Sûreté Vérification DE L’ANGLE DE CoupeInterrupteur Guide D’ALIGNEMENT RéglableCoupes Régulieres Sciage DES Matériaux DE Maçonnerie ET DES MétauxCoupe DE Grandes Feuilles Coupes EN GuichetCoupes DE Refente Utilisation D’UNE Planche Comme Guide DE RefenteTémoin D’ÉTAT DE Charge DE LA Pile Dépose ET Repose DU BLOC-PILESChargement DU BLOC-PILES Chargeur Rapide Remarques Importantes Concernant LA Charge Montage du chargeur Montage DU Chargeur À UNE Surface VerticaleEnlevez le bloc-piles du chargeur avant de fixer ce dernier Accessoires EntretienNettoyage Seguridad eléctrica Area de trabajoSeguridad personal Personales gravesNormas de seguridad para sierras circulares ServicioÁrea de corte y de la hoja POR EL Operador Batería/cargador Eliminación de las baterías Cuidado de las bateríasBaterías DE NIQUEL-CADMIO Cadmio Ni-Cd indica que RobertSímbolos Con aislamiento dobleDe Ni-Cd Sierra circular sin cordón Descripción funcional y especificacionesHerramienta CargadorAjustes o cambiar accesorios. Dichas medidas EnsamblajeInterruptor DE Sequridad Instrucciones de funcionamientoVerificacion DEL Angulo DE Corte DE 90˚ Ajuste DE InclinacionGuia DE Interruptor Guia DE Linea AjustableCortes Generales Movimiento libre del protector inferiorCorte DE Planchas Grandes Cortes DE BolsillosCortes AL Hilo TABLERO-GUIA Para Cortar AL HiloIndicador DE Estado Cargado DE LA Batería Liberacion E Insercion Delpaquete DE BateriasCarga DEL Paquete DE Baterías Cargador Rápido Notas Importantes Para Cargar Montaje DEL Cargador EN UNA Superficie Vertical Montaje del cargadorMantenimiento AccesoriosLimpieza Remarques Notas
Top Page Image Contents