Skil 2895 Battery/Charger, Battery Care, Nails, screws, keys, etc. Fire or injury may result

Page 5

SM 1619X03409 05-08 5/6/08 2:45 PM Page 5

Battery/Charger

Before using battery charger, read all instructions and cautionary markings on

(1)battery charger, (2) battery pack, and (3) product using battery.

Use only the charger which accompanied your product or direct replacement as listed in the catalog or this manual. Do not substitute any other charger. Use only Skil approved chargers with your product. See Functional Description and Specifications.

Do not disassemble charger or operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any way. Replace damaged cord or plugs immediately. Incorrect reassembly or damage may result in electric shock or fire.

Do not recharge battery in damp or wet environment. Do not expose charger to rain or snow. If battery case is cracked or otherwise damaged, do not insert into charger. Battery short or fire may result.

Charge only Skil approved rechargeable batteries. See Functional Description and Specifications. Other types of batteries may burst causing personal injury and damage.

Charge battery pack in temperatures above +40 degrees F (4 degrees C) and

below +105 degrees F (41 degrees C). Store tool and battery pack in locations where temperatures will not exceed 120 degrees F (49 degrees C). This is important to prevent serious damage to the battery cells.

Battery leakage may occur under extreme usage or temperature conditions. Avoid contact with skin and eyes. The battery liquid is caustic and could cause chemical burns to tissues. If liquid comes in contact with skin, wash quickly with soap and water, then with lemon juice or vinegar. If the liquid contacts your eyes, flush them with water for a minimum of 10 minutes and seek medical attention.

Place charger on flat non-flammable surfaces and away from flammable materials when re-charging battery pack. The charger and battery pack heat during charging. Carpeting and other heat insulating surfaces block proper air circulation which may cause overheating of the charger and battery pack. If smoke or melting of the case are observed unplug the charger immediately and do not use the battery pack or charger.

Use of an attachment not recom- mended or sold by Skil may result in a risk of fire, electric shock or injury to persons.

Battery Care

!WARNING When batteries are not in tool or charger, keep them

away from metal objects. For example, to protect terminals from shorting, DO NOT place batteries in a tool box or pocket with

nails, screws, keys, etc. Fire or injury may result.

DO NOT PUT BATTERIES INTO FIRE OR EXPOSE TO HIGH HEAT. They may explode.

-5-

Image 5
Contents See Voir Ver la página Read Before UsingFor English Version Version française Work area safety General Safety RulesElectrical safety Personal safetyBattery tool use and care Power tool use and careService Power tools are dangerous in the hands of untrained usersExposure to noise can cause hearing loss Safety Rules for Cordless Drills/DriversNails, screws, keys, etc. Fire or injury may result Battery/ChargerBattery Care NICKEL-METAL Hydride Batteries Battery DisposalNICKEL-CADMIUM Batteries Symbols Cordless Drills/Driver Functional Description and SpecificationsOperating Instructions Inserting Bits Clockwise Counter Installing ChuckRemoving Chuck Door Batteries Protective Plastic InsertBattery Release Button Indicator Light Charging Battery Pack Fast Charger Releasing and InsertingRED LED Green LED Yellow LED ButtonImportant Charging Notes Mounting Charger Operating Tips Maintenance Certain cleaning agents Caution and solvents damage AccessoriesCleaning Sécurité du lieu de travail Consignes générales de sécuritéSécurité électrique Sécurité personnelleEntretien Utilisation et entretien des outils ÉlectroportatifsUtilisation et entretien des outils à piles Le plomb provenant des peintures à base de plomb Consignes de sécurité pour perceuses/tournevis sans cordonEntretien des piles Chargeur de pileNe tentez pas de Mise au rebut des pilesPiles NICKEL-CADMIUM Volontairement à un programme industriel deSymboles Perceuses/tournevis sans cordon Description fonctionnelle et spécificationsOutil Bloc pilesConsignes de fonctionnement De la perceuse en Insertion DES ForetsRetrait DU Mandrin Sens ANTI-HORAIRE Pose DU MandrinVoyant Vert Voyant Jaune Voyant RougeBLOC-PILESCHARGEUR LA Pile Témon LumineuxRemarques Importantes Concernant LA Charge Montage DU Chargeur À UNE Surface Verticale Montage du chargeurEnlevez le bloc-piles du chargeur avant de fixer ce dernier Compartiment DE Rangement DES Embouts ChargeurConsignes de fonctionnement Entretien Nettoyage AccessoiresCertains Agents Et certainsSeguridad del área de trabajo Normas generales de seguridadSeguridad eléctrica Seguridad personalServicio de ajustes y reparaciones MecánicasUso y cuidado de las herramientas Alimentadas por baterías SM 1619X03409 05-08 5/6/08 245 PM Cuidado de las baterías Batería/cargadorBaterías DE NIQUEL-HIDRURO Metalico Eliminación de las bateríasBaterías DE NIQUEL-CADMIO De Ni-Cd SímbolosCon aislamiento doble Taladros/destornilladores sin cordón Descripción funcional y especificacionesCambio DE Engranajes Mandril SIN LlavePalanca DE AVANCE/INVERSIÓN Cierre DEL Gatillo Instrucciones de funcionamientoEmbrague Ajustable FrenoDesmontaje DEL Mandril Colocacion DE LAS BrocasEl punto medio de las dos marcas es el centro del LED RojoLED Verde LED Amarillo Botón LíneaNotas Importantes Para Cargar Montaje DEL Cargador EN UNA Superficie Vertical Montaje del cargadorCargador Para Desbloquear Bloquear Paquete DE Batería CargadorSujecion CON Tornillos Consejos de funcionamientoBrocas Para Taladro Taladrado DE MaderaServicio MantenimientoLimpieza AccesoriosCordones de extensión Para evitarRemarques Notas SM 1619X03409 05-08 5/6/08 245 PM