Siemens G85139 operating instructions Basic Operation, General, Initial Testing

Page 15

3. FRONT PANEL CONTROLS & BASIC OPERATION

English

3.2 Basic Operation

Refer to section 5 for a full description of each parameter.

3.2.1 General

(1)The inverter does not have a main power switch and is live when the mains supply is connected. It waits, with the output disabled, until the RUN button is pressed or for the presence of a digital ON signal at terminal 5 (rotate right) or terminal 6 (rotate left) - see parameters P051 - P053.

(2)If output frequency is selected to be displayed (P001 = 0), the corresponding setpoint is displayed approximately every 1.5 seconds while the inverter is stopped.

(3)The inverter is programmed at the factory for standard applications on Siemens four-pole standard motors. When using other motors it is necessary to enter the specifications from the motor’s rating plate into parameters P081 to P085 (see Figure 10). Note: Access to these parameters is not possible unless P009 has been set to 002 or 003.

P084

P081

	3 Mot	1LA5053-2AA20
	IEC 56	Nr. E D510 3053		12 022
	IM B3	Nr. E D510 3053		12 022
	IM B3	IP54	Rot. KL 16	I.Cl.F
		IP54	Rot. KL 16	I.Cl.F
	50 Hz 220/380 VΔ/Y	60 Hz	440 V Y
	0,61/0,35 A		0,34 A
	0,12 kW		0,14 kW
	cosϕ 0,81	cosϕ 0,81
	2745 /min		3310 /min
	VDE 0530	S.F. - 1,15

P083 P082 P085

Figure 10: Typical Motor Rating Plate Example

Note: Ensure that the inverter is configured correctly to the motor, i.e. in the above example delta terminal connection is for 220 V.

3.2.2 Initial Testing

(1)Check that all cables have been connected correctly (section 2) and that all relevant product and plant/location safety precautions have been complied with.

(2)Apply mains power to the inverter.

(3)Ensure that it is safe to start the motor. Press the RUN button on the inverter. The display will change to 5.0 and the motor shaft will begin to turn. It will take one second for the inverter to ramp up to 5 Hz.

(4)Press the STOP button. The display will change to 0.0 and the motor slow to a complete stop within one second.

© Siemens plc 1997G85139-H1750-U049-B

15	26/09/97

Image 15

Contents Micromaster Safety Instructions Overview Wiring Guidelines to Minimise the Effects of EMI InstallationExample of an RFI Suppression Filter Installation Mechanical Installation Ideal InstallationHazard 141 160 175 184 149 172 174 138 215 185 195 204 232 MMxxx MMxxx/2 ModelMMxxx/3 500 Frame Sizes All measurements in mmPower and Motor Connections Frame Size a Electrical InstallationPower Connections Single PhasePower Connections Access Diagram Frame Size B Power and Motor Connections Frame Size BPower Connections Access Diagram Frame Size C Power and Motor Connections Frame Size CControl Connections Front Panel RS485 D-typeControl Terminal Block Motor Overload Protection Block DiagramFront Panel Controls Front Panel Controls & Basic OperationRefer to for a full description of each parameter Initial TestingBasic Operation GeneralBasic Operation 10 Step Guide Step /ActionButton Display Analogue Control Operating Modes 4.1 Digital ControlLocal and Remote Control Stopping the MotorIf the Motor Does Not Start Up General Description Hardware SetupParameter Settings Closed Loop ControlSystem Parameters Description / Notes P000Function Range Operating displayFunction P004 ∙P005 ∙ P006 P007 P009 ∙P017 ∙ P018 ∙ P011P012 ∙ P013 ∙ P014 ∙ P015 ∙ P016 ∙See P014 P022 ∙P023 ∙ P024 ∙ P027 ∙ P028 ∙ P029 ∙ P031 ∙ P032 ∙P041 ∙ P042 ∙ P043 ∙ P044 ∙ P045 P046 ∙ P047 ∙ P048 ∙ P050P050 = P050 = 6 or P056 P051P052 P053P064 P061P062 P063P066 P073 ∙P074 ∙ P076 ∙ Inverter output terminals with power off P077P079 ∙ P081 P082 P083 P084 P085 P089 ∙ P091 ∙ P111 P112P113 P124 P121P122 P123P944 P971 ∙ Eeprom storage control P947 P958 P963 P967 P968 P970Cause Fault CodesFault Code F151 F15316-8BB40 21-0BC40 SpecificationsSiemens sales office for Options / AccessoriesAppropriate manner see .1 Please contact your localUSS Status Codes Setup procedure for a simple applicationSupplementary Information Application ExampleStandard Electro-Magnetic Compatibility EMCClass 1 General Industrial EMC PhenomenonClass 2 Filtered Industrial IEC 1000-2-4 ENV 50Standard Level Filter Class Filter Part No Environmental AspectsModel No EMC ClassP947 P958 P963 P967 P968 P970 P971 User’s Parameter SettingsP702 P880 P910 P918 P922 P923 P927 P928 P930 P931 P944Bestell-Nr SE9286-4AA86