Siemens G85139 operating instructions Example of an RFI Suppression Filter Installation

Page 5

2. INSTALLATION

English

MAINS POWER

CABLE

Connect to Mains and

PE terminals on Inverter

CONTROL

CABLE

EARTH STUD

FILTER UNIT

Note: There must be a good

conductive bond between filter and

metal panel.

EARTH STUD

(under)

SCREENED

CABLE

When cable glands cannot be used, terminate screen to metal panel by removing cable sheath.

SCREENED

When attempting to meet specific EMC limits by using a filter,

the following points must be observed:

CABLE

 

 

(1)

All cables to and from the inverter (including control

 

 

 

 

 

cables) must be screened using suitable glands.

 

 

(2)

The control cable must be kept separate from the motor

 

 

 

 

 

and mains cables.

 

MOTOR * Note: Screen must be terminated

 

CABLE *

 

at the motor.

Figure 1: Example of an RFI Suppression Filter Installation

© Siemens plc 1997G85139-H1750-U049-B

5

26/09/97

 

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Micromaster Safety Instructions Overview Wiring Guidelines to Minimise the Effects of EMI InstallationExample of an RFI Suppression Filter Installation Hazard Mechanical InstallationIdeal Installation MMxxx/3 500 MMxxx MMxxx/2 ModelFrame Sizes All measurements in mm 141 160 175 184 149 172 174 138 215 185 195 204 232Power and Motor Connections Frame Size a Electrical InstallationPower Connections Single PhasePower Connections Access Diagram Frame Size B Power and Motor Connections Frame Size BPower Connections Access Diagram Frame Size C Power and Motor Connections Frame Size CControl Terminal Block Control ConnectionsFront Panel RS485 D-type Motor Overload Protection Block DiagramFront Panel Controls Front Panel Controls & Basic OperationBasic Operation Initial TestingGeneral Refer to for a full description of each parameterButton Display Basic Operation 10 Step GuideStep /Action Analogue Control Operating Modes 4.1 Digital ControlIf the Motor Does Not Start Up Local and Remote ControlStopping the Motor Parameter Settings Hardware SetupClosed Loop Control General DescriptionSystem Parameters Function Range P000Operating display Description / NotesP005 ∙ P006 P007 P004 ∙P009 ∙ FunctionP012 ∙ P013 ∙ P014 ∙ P015 ∙ P011P016 ∙ P017 ∙ P018 ∙P023 ∙ P024 ∙ P022 ∙P027 ∙ P028 ∙ P029 ∙ P031 ∙ P032 ∙ See P014P050 = P050 = 6 or P041 ∙ P042 ∙ P043 ∙ P044 ∙ P045P046 ∙ P047 ∙ P048 ∙ P050 P052 P051P053 P056P062 P061P063 P064P074 ∙ P076 ∙ P066P073 ∙ P079 ∙ P081 P082 P083 P084 P085 P089 ∙ P091 ∙ Inverter output terminals with power offP077 P113 P111P112 P122 P121P123 P124P944 P971 ∙ Eeprom storage control P947 P958 P963 P967 P968 P970Fault Code Fault CodesF151 F153 Cause16-8BB40 21-0BC40 SpecificationsAppropriate manner see .1 Options / AccessoriesPlease contact your local Siemens sales office forSupplementary Information Setup procedure for a simple applicationApplication Example USS Status CodesClass 1 General Industrial Electro-Magnetic Compatibility EMCEMC Phenomenon StandardStandard Level Class 2 Filtered IndustrialIEC 1000-2-4 ENV 50 Model No Environmental AspectsEMC Class Filter Class Filter Part NoP702 P880 User’s Parameter SettingsP910 P918 P922 P923 P927 P928 P930 P931 P944 P947 P958 P963 P967 P968 P970 P971Bestell-Nr SE9286-4AA86
Top Page Image Contents