Siemens G85139 operating instructions Basic Operation 10 Step Guide, Step /Action, Button Display

Page 16

English

3. FRONT PANEL CONTROLS & BASIC OPERATION

3.2.3 Basic Operation - 10 Step Guide

The basic method of setting up the inverter for use is described below. This method uses a digital frequency setpoint and requires only the minimum number of parameters to be changed from their default settings. It assumes that a standard Siemens four-pole motor is connected to the inverter (see section 3.2.1 if a different motor type is being used).

Step /Action

1. Apply mains power to the inverter.

The display will alternate between the actual frequency (0.0 Hz) and the requested frequency setpoint (5.0 Hz default).

2.Press the parameterisation button.

3.Press the Δ button until parameter P005 is displayed.

4.Press P to display the current frequency setpoint (5 Hz is the factory default setting).

5.Press the Δ button to set the desired frequency setpoint

(e.g. 35 Hz).

Button

P

P

Display

6.Press P to lock the setting into memory. 7, Press the ∇ button to return to P000.

8. Press P to exit the parameterisation procedure.

The display will alternate between the current frequency and the requested frequency setpoint.

9. Start the inverter by pressing the RUN button.

The motor shaft will start to turn and the display will show that the inverter is ramping up to the setpoint of 35 Hz.

Note

The setpoint will be achieved after 7 seconds (35 Hz/50 Hz x 10 s *). If required, the motor’s speed (i.e. frequency) can be varied directly by using the Δ ∇ buttons. (Set P011 to 001 to enable the new frequency setting to be retained in memory during periods when the inverter is not running.)

10. Switch the inverter off by pressing the STOP button.

The motor will slow down and come to a controlled stop (takes 7 s **).

*Default ramp-up time is 10 s to reach 50 Hz (defined by P002 and P013).

**Default ramp-down time is 10 s from 50 Hz (defined by P003 and P013).

P

P

G85139-H1750-U049-B	© Siemens plc 1997
26/09/97	16
	16

Image 16

Contents Micromaster Safety Instructions Overview Installation Wiring Guidelines to Minimise the Effects of EMIExample of an RFI Suppression Filter Installation Ideal Installation Mechanical InstallationHazard MMxxx MMxxx/2 Model MMxxx/3 500Frame Sizes All measurements in mm 141 160 175 184 149 172 174 138 215 185 195 204 232Electrical Installation Power and Motor Connections Frame Size aSingle Phase Power ConnectionsPower and Motor Connections Frame Size B Power Connections Access Diagram Frame Size BPower and Motor Connections Frame Size C Power Connections Access Diagram Frame Size CFront Panel RS485 D-type Control ConnectionsControl Terminal Block Block Diagram Motor Overload ProtectionFront Panel Controls & Basic Operation Front Panel ControlsInitial Testing Basic OperationGeneral Refer to for a full description of each parameterStep /Action Basic Operation 10 Step GuideButton Display Operating Modes 4.1 Digital Control Analogue ControlStopping the Motor Local and Remote ControlIf the Motor Does Not Start Up Hardware Setup Parameter SettingsClosed Loop Control General DescriptionSystem Parameters P000 Function RangeOperating display Description / NotesP004 ∙ P005 ∙ P006 P007P009 ∙ FunctionP011 P012 ∙ P013 ∙ P014 ∙ P015 ∙P016 ∙ P017 ∙ P018 ∙P022 ∙ P023 ∙ P024 ∙P027 ∙ P028 ∙ P029 ∙ P031 ∙ P032 ∙ See P014P046 ∙ P047 ∙ P048 ∙ P050 P041 ∙ P042 ∙ P043 ∙ P044 ∙ P045P050 = P050 = 6 or P051 P052P053 P056P061 P062P063 P064P073 ∙ P066P074 ∙ P076 ∙ P077 Inverter output terminals with power offP079 ∙ P081 P082 P083 P084 P085 P089 ∙ P091 ∙ P112 P111P113 P121 P122P123 P124P944 P947 P958 P963 P967 P968 P970 P971 ∙ Eeprom storage controlFault Codes Fault CodeF151 F153 CauseSpecifications 16-8BB40 21-0BC40Options / Accessories Appropriate manner see .1Please contact your local Siemens sales office forSetup procedure for a simple application Supplementary InformationApplication Example USS Status CodesElectro-Magnetic Compatibility EMC Class 1 General IndustrialEMC Phenomenon StandardIEC 1000-2-4 ENV 50 Class 2 Filtered IndustrialStandard Level Environmental Aspects Model NoEMC Class Filter Class Filter Part NoUser’s Parameter Settings P702 P880P910 P918 P922 P923 P927 P928 P930 P931 P944 P947 P958 P963 P967 P968 P970 P971Bestell-Nr SE9286-4AA86