Siemens G85139 Supplementary Information, Application Example, USS Status Codes

Page 37

8. SUPPLEMENTARY INFORMATIONEnglish

8. SUPPLEMENTARY INFORMATION

8.1 Application Example

Setup procedure for a simple application

Motor:	220 V
	1.5 kW output power
Application requirements:	Setpoint adjustable via potentiometer 0 - 50 Hz
	Ramp up from 0 to 50 Hz in 15 seconds
	Ramp down from 50 to 0 Hz in 20 seconds
Inverter used:	MM150 (6SE9216-8BB40)
Settings:	P009 = 2 (all parameters can be altered)
	P081	- P085 = values given on motor rating plate
	P006	= 1 (analogue input)
	P002	= 15 (ramp up time)
	P003	= 20 (ramp down time)

This application is now to be modified as follows:

Operation of motor up to 75 Hz	i.e.	V
(voltage/frequency curve is linear up to 50 Hz).	i.e.	V
(voltage/frequency curve is linear up to 50 Hz).		220
Motor potentiometer setpoint in addition to		220
analogue setpoint .
Use of analogue setpoint at maximum 10 Hz.
Ramp times to remain the same.		50	75
		50	75	f (Hz)
				f (Hz)


Parameter adjustments:	P009 = 2		(all parameters can be altered)
	P013	= 75		(maximum motor frequency in Hz)
	P006	= 2	(setpoint via motor potentiometer or fixed setpoint)
	P024	= 1	(analogue setpoint is added)
	P022	= 10		(maximum analogue setpoint at 10 V = 10 Hz)

8.2 USS Status Codes

The following list gives the meaning of status codes displayed on the front panel of the inverter when the serial link is in use and parameter P001 is set to 006:

001Message OK

002Slave address received

100Invalid start character

101Timeout

102Checksum error

103Incorrect message length

104Parity fail

Notes

(1)The display flashes whenever a byte is received, thus giving a basic indication that a serial link connection is established.

(2)If ‘100’ flashes on the display continuously, this usually indicates a bus termination fault.

© Siemens plc 1997G85139-H1750-U049-B

37	26/09/97

Image 37

Contents Micromaster Safety Instructions Overview Wiring Guidelines to Minimise the Effects of EMI InstallationExample of an RFI Suppression Filter Installation Ideal Installation Mechanical InstallationHazard MMxxx/3 500 MMxxx MMxxx/2 ModelFrame Sizes All measurements in mm 141 160 175 184 149 172 174 138 215 185 195 204 232Power and Motor Connections Frame Size a Electrical InstallationPower Connections Single PhasePower Connections Access Diagram Frame Size B Power and Motor Connections Frame Size BPower Connections Access Diagram Frame Size C Power and Motor Connections Frame Size CFront Panel RS485 D-type Control ConnectionsControl Terminal Block Motor Overload Protection Block DiagramFront Panel Controls Front Panel Controls & Basic OperationBasic Operation Initial TestingGeneral Refer to for a full description of each parameterStep /Action Basic Operation 10 Step GuideButton Display Analogue Control Operating Modes 4.1 Digital ControlStopping the Motor Local and Remote ControlIf the Motor Does Not Start Up Parameter Settings Hardware SetupClosed Loop Control General DescriptionSystem Parameters Function Range P000Operating display Description / NotesP005 ∙ P006 P007 P004 ∙P009 ∙ FunctionP012 ∙ P013 ∙ P014 ∙ P015 ∙ P011P016 ∙ P017 ∙ P018 ∙P023 ∙ P024 ∙ P022 ∙P027 ∙ P028 ∙ P029 ∙ P031 ∙ P032 ∙ See P014P046 ∙ P047 ∙ P048 ∙ P050 P041 ∙ P042 ∙ P043 ∙ P044 ∙ P045P050 = P050 = 6 or P052 P051P053 P056P062 P061P063 P064P073 ∙ P066P074 ∙ P076 ∙ P077 Inverter output terminals with power offP079 ∙ P081 P082 P083 P084 P085 P089 ∙ P091 ∙ P112 P111P113 P122 P121P123 P124P944 P971 ∙ Eeprom storage control P947 P958 P963 P967 P968 P970Fault Code Fault CodesF151 F153 Cause16-8BB40 21-0BC40 SpecificationsAppropriate manner see .1 Options / AccessoriesPlease contact your local Siemens sales office forSupplementary Information Setup procedure for a simple applicationApplication Example USS Status CodesClass 1 General Industrial Electro-Magnetic Compatibility EMCEMC Phenomenon StandardIEC 1000-2-4 ENV 50 Class 2 Filtered IndustrialStandard Level Model No Environmental AspectsEMC Class Filter Class Filter Part NoP702 P880 User’s Parameter SettingsP910 P918 P922 P923 P927 P928 P930 P931 P944 P947 P958 P963 P967 P968 P970 P971Bestell-Nr SE9286-4AA86