Siemens G85139 operating instructions P000, Function Range, Operating display, Description / Notes

Page 21

5. SYSTEM PARAMETERS

Parameter		Function		Range
				[Default]
				[Default]

P000		Operating display	-

P001 ∙ Display mode	0 - 8
	[0]

P002 ∙ Ramp up time (seconds)	0 - 650.00
	[10.00]

P003 ∙ Ramp down time (seconds)			0 - 650.00
			[10.00]

English

Description / Notes

This displays the output selected in P001.

In the event of a fault, the relevant fault code (Fxxx) is displayed (see section 6). In the event of a warning the display flashes. If output frequency has been selected (P001 = 0) and the inverter is OFF, the display alternates between the selected frequency and the actual frequency.

Display selection:

0 = Output frequency (Hz)

1 = Frequency setpoint (i.e. speed at which inverter is set to run) (Hz)

2 = Motor current (A)

3= DC-link voltage (V)

4= Not used

5= Motor RPM

6= USS status (see section 8.2)

7= Closed loop control setpoint (% of full scale)

8= Output voltage

This is the time taken for the motor to accelerate from standstill to the maximum frequency as set in P013.

Setting the ramp up time too short can cause the inverter to trip (fault code F002 - overcurrent).

F re q u e n c y
fm a x
0 H z	R a m p u p	T im e
	R a m p u p
	tim e
	tim e
	(0 - 6 5 0 s )

This is the time taken for the motor to decelerate from maximum frequency (P013) to standstill.

Setting the ramp down time too short can cause the inverter to trip (fault code F001 - overvoltage).

This is also the period for which DC injection braking is applied (see P073)

F re q u e n c y
fm a x
0 H z	R a m p d o w n			T im e
	R a m p d o w n
		tim e
	(0	tim e	s )
	(0	- 6 5 0	s )

© Siemens plc 1997G85139-H1750-U049-B

21	26/09/97

Image 21

Contents Micromaster Safety Instructions Overview Wiring Guidelines to Minimise the Effects of EMI InstallationExample of an RFI Suppression Filter Installation Mechanical Installation Ideal InstallationHazard MMxxx/3 500 MMxxx MMxxx/2 ModelFrame Sizes All measurements in mm 141 160 175 184 149 172 174 138 215 185 195 204 232Power and Motor Connections Frame Size a Electrical InstallationPower Connections Single PhasePower Connections Access Diagram Frame Size B Power and Motor Connections Frame Size BPower Connections Access Diagram Frame Size C Power and Motor Connections Frame Size CControl Connections Front Panel RS485 D-typeControl Terminal Block Motor Overload Protection Block DiagramFront Panel Controls Front Panel Controls & Basic OperationBasic Operation Initial TestingGeneral Refer to for a full description of each parameterBasic Operation 10 Step Guide Step /ActionButton Display Analogue Control Operating Modes 4.1 Digital ControlLocal and Remote Control Stopping the MotorIf the Motor Does Not Start Up Parameter Settings Hardware SetupClosed Loop Control General DescriptionSystem Parameters Function Range P000Operating display Description / NotesP005 ∙ P006 P007 P004 ∙P009 ∙ FunctionP012 ∙ P013 ∙ P014 ∙ P015 ∙ P011P016 ∙ P017 ∙ P018 ∙P023 ∙ P024 ∙ P022 ∙P027 ∙ P028 ∙ P029 ∙ P031 ∙ P032 ∙ See P014P041 ∙ P042 ∙ P043 ∙ P044 ∙ P045 P046 ∙ P047 ∙ P048 ∙ P050P050 = P050 = 6 or P052 P051P053 P056P062 P061P063 P064P066 P073 ∙P074 ∙ P076 ∙ Inverter output terminals with power off P077P079 ∙ P081 P082 P083 P084 P085 P089 ∙ P091 ∙ P111 P112P113 P122 P121P123 P124P944 P971 ∙ Eeprom storage control P947 P958 P963 P967 P968 P970Fault Code Fault CodesF151 F153 Cause16-8BB40 21-0BC40 SpecificationsAppropriate manner see .1 Options / AccessoriesPlease contact your local Siemens sales office forSupplementary Information Setup procedure for a simple applicationApplication Example USS Status CodesClass 1 General Industrial Electro-Magnetic Compatibility EMCEMC Phenomenon StandardClass 2 Filtered Industrial IEC 1000-2-4 ENV 50Standard Level Model No Environmental AspectsEMC Class Filter Class Filter Part NoP702 P880 User’s Parameter SettingsP910 P918 P922 P923 P927 P928 P930 P931 P944 P947 P958 P963 P967 P968 P970 P971Bestell-Nr SE9286-4AA86