Hitachi CJ120VA instruction manual Make Them Available to Other Users Owners of this Tool

Page 8

English

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. “Double insulation” means that two physically separated insulation systems have been used to insulate the electrically conductive materials connected to the power supply from the outer frame handled by the operator. Therefore, either the symbol “” or the words “Double insulation” appear on the power tool or on the nameplate.

Although this system has no external grounding, you must still follow the normal electrical safety precautions given in this Instruction Manual, including not using the power tool in wet environments.

To keep the double insulation system effective, follow these precautions:

◯Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this power tool, and only genuine HITACHI replacement parts should be installed.

◯Clean the exterior of the power tool only with a soft cloth moistened with soapy water, and dry thoroughly.

Never use solvents, gasoline or thinners on plastic components; otherwise the plastic may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

8

Image 8

Contents Avertissement AdvertenciaÍndice ContentsTable DES Matieres Important Safety Information Meanings of Signal WordsSafety General Safety RulesEnglish Specific Safety Rules and Symbols Do not wipe plastic parts with solvent Operate power tools at the rated voltageNever use a tool which is defective or operating abnormally Make Them Available to Other Users Owners of this Tool Double Insulation for Safer OperationName of Parts SpecificationsFunctional Description Prior to Operation Assembly and OperationApplications Changing blades Adjusting the blade operating speedAdjusting the orbital operation Cutting stainless steel plates Splinter guardChip cover Sub baseCutting Rectilinear cuttingSawing curved lines Cutting a circle or a circular arcConcerning Cutting of Stainless Steel Plates Cutting metallic materialsPocket cutting Angular cuttingHousing the Allen Wrench Adjust the speedSelection of Blades Set the orbital position toConnecting with Cleaner Maintenance and Inspection No.11 Accessories Standard AccessoriesInformations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTSecurite Regles Generale DE SecuriteConserver CES Instructions Avertissement Lire et coxmprendre toutes les instructionsFrançais Regles DE Securite Specifiques ET Symboles NE Jamais toucher les parties mobilesNe pas essuyer les parties en plastique avec du solvant Garder propres les évents d’air du moteurUtiliser l’outil motorisé à la tension nominale Double Isolation Pour UN Fonctionnement Plus SUR Remarque Description FonctionnelleNOM DES Parties Avant L’UTILISATION Remplacement des lames PrecautionsRéglage de la vitesse de fonctionnement de la lame Réglage du fonctionnement orbitalDécoupage de plaques en acier inoxydable Anti-éclatsCouvercle d’éclats Socle auxiliairePrecaution CoupeCoupe rectilinéaire Sciage de lignes courbesAU Sujet DU Decoupage DE Plaques EN Acier Inoxydable Coupe de matériaux métalliquesDécoupe d’ouvertures Coupe angulaireChoix DES Lames Rangement DES Lames DE LA CLÉ AllenPour régler la vitesse Régler la position orbitale surRaccordement AU Nettoyeur Entretien ET Inspection Tableau 1 Liste des lames appropriées Accessoires Accessoires StandardInformación Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónSeguridad Normas Generales DE SeguridadGuarde Estas Instrucciones Advertencia Lea y entienda todas las instruccionesEspañol Normas Y Símbolos Específicos DE Seguridad No toque Nunca las piezas móvilesUtilice la herramienta correcta Maneje correctamente la herramientaManeje con cuidado las herramientas eléctricas No limpie las partes de plástico con disolventeVoltios Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Descripción Funcional NomenclaturaEspecificaciones NotaAntes DE LA Operación Montaje Y OperaciónAplicaciones Cambio de las cuchillas Ajustar la velocidad de operación de la cuchillaAjuste del funcionamiento orbital PrecaucionCorte de chapas de acero inoxidable Protector contra astillasCubierta de virutas Base secundariaCortar Corte para rectilinearSerrar líneas curvas Cortar en circulo o un arco circularCorte angular Cortar materiales metálicosRecorte interior Sobre EL Corte DE Chapas DE Acero Inoxidable Seleccion DE LAS CuchillasAjuste la velocidad Ajuste la posición orbital aAlojamiento DE LA Llave Allen Conexion CON EL LimpiadorMantenimiento E Inspección Maderaútil General Cuchilla Calidad dematerial Material AcortarAccesorios Accesorios Estándar608DDC2PS2L CJ120VA Page Page Page Hitachi Koki Canada Co