Hitachi L300P Series service manual Others

Function mode

	Code	Function name					SJ300 Setting range	Initial data	Note
								-FE/-FU/-F
	b034	RUN time/Power ON time level					0.-9999./1000-6553(10000-65530)hr	0.
	b035	Operation direction restrict					00(Reverse is valid)/01(Only forward)/02(Only reverse)	00
	b036	Start reduced voltage					00(Start reduced voltage time small)-06(Start reduced voltage time large)	06
	b037	Display selection					00(all display)/01(each function display)/02(User setting / main setting)	00
	b040	Torque limit mode selection					00(4 quadrant mode)/01(Terminal operation)/	00
							02(Analog input)/03(Option1)/04(Option2)
	b041	Torque limit level 1 setting					0.-200.(%)/no(Invalid) <0.-180.(%)/no(Invalid)>	150.
		(Forward-driving at
		4 quadrant mode)
		Torque limit level 2 setting
	b042	(Reverse-regenerating at					0.-200.(%)/no(Invalid) <0.-180.(%)/no(Invalid)>	150.
		4 quadrant mode)
		Torque limit level 3 setting
	b043	(Reverse-driving at					0.-200.(%)/no(Invalid) <0.-180.(%)/no(Invalid)>	150.
		4 quadrant mode)
		Torque limit level 4 setting
	b044	(Forward-regenerating at					0.-200.(%)/no(Invalid) <0.-180.(%)/no(Invalid)>	150.
		4 quadrant mode)
	b045	Torque LAD-STOP selection					00(Invalid)/01(Valid)	00
	b046	Reverse run prevention					00(Invalid)/01(Valid)	00
		selection
	b050	Selection of non-stop					00(Invalid)/01(Valid)	00
		function at instantaneous
		power failure
	b051	Start voltage of non-stop					0.0-1000.(V)	0.0
		function setting
	b052	OV LAD-STOP level of non-					0.0-1000.(V)	0.0
		stop function setting
others	b053	Deceleration		time	of	non-	0.01-99.99/100.0-999.9/1000.-3600.(s)	1.00
		stop function setting
	b054	Deceleration frequency widt h					0.00-10.00(Hz)	0.00
The		of non-stop function setting
	b080	AM adjustment					0. - 255.	180
	b081	FM adjustment					0. - 255.	60
	b082	Start frequency adjustment					0.10-9.99(Hz)	0.50
	b083	Carrier frequency setting					0.5-15.0(kHz) Derating enable, <0-10kHz>	5.0 <3.0>
	b084	Initialize mode					00(Trip history clear)/01(Data initialization)/	00
							02(Trip history clear + data initialization)
	b085	Country code for initialization					00(Interior)/01(EC)/02(USA)	01/02/00
	b086	Frequency scalar conversion					0.1-99.9	1.0
		factor
	b087	STOP key enable					00(valid)/01(invalid)	00
	b088	Resume on FRS cancellation					00(0Hz start)/01(Start f-equaling)	00
		mode
	b090	BRD usage ratio					0.0-100.0(%)	0.0
	b091	Stop mode selection					00(deceleration stop)/01(Free-run stop)	00
	b092	Cooling fan control					00(Always ON)/	00
							01(ON during run, After power ON, then for 5 minutes on stop is implied.)
	b095	BRD selection					00(invalid)/01(valid<invalid during stop>)/02(valid<valid during stop>)	00
	b096	BRD ON level					330-380/660-760(V)	360/720
	b098	Thermistor selection					00(invalid)/01(Positive temperature coefficient enable)/02 (NTC enable)	00
	b099	Thermistor error level					0. - 9999. ( ohm)	3000.
	b120	Braking control selection					00(Invalid)/01(valid)	00
	b121	Waiting time		for	releasing		0.00-5.00(s)	0.00
		braking conformation
	b122	Waiting time for acceleration					0.00-5.00(s)	0.00
	b123	Waiting time for stop					0.00-5.00(s)	0.00
	b124	Waiting	time for			signal	0.00-5.00(s)	0.00
		conformation
	b125	Releasing frequency					0.00-99.99/100.0-400.0(Hz)	0.00
								Rated
	b126	Releasing current					0.00*rated current-2.00*rated current(A)	current of
								inverter
	C091	Debug mode selection					00(No display)/01(Display)	00
	C101	UP/DWN selection					00(No frequency data)/01(Keep frequency data)	00
	C102	Reset selection					00(Trip cancel during ON)/01(Trip cancel during OFF)/	00
							02(Valid only during trip<Cancel during ON>)
	C103	Reset f	frequency matching				00(0Hz start)/01(Start f-equaling)	00
		selection
		Overload	advance			notice		Inverter
	C111						0.0-2.0*rated current(A)	rated
		level
								current
	C121	O zero adjustment					0.-9999./1000-6553(10000-65530)	Set on
								forwarding
	C122	OI zero adjustment					0.-9999./1000-6553(10000-65530)	Set on
								forwarding
	C123	O2 zero adjustment					0.-9999./1000-6553(10000-65530)	Set on
								forwarding

(Note) < > indicate the setting range of 75 to 150kW

1- 7