Hitachi L300P Series service manual 2nd motor

Function mode

	Code	Function name	SJ300 Setting range	Initial data	Note
				-FE/-FU/-F
	b012	Electronic thermal level	0.2*constant current-1.20*constant current(A)	Rated
				Current of
				inverter
	b212	Electronic thermal level	0.2*constant current-1.20*constant current(A)	Rated
				Current of
		(2nd motor)
				Inverter
	b312	Electronic thermal level	0.2*constant current-1.20*constant current(A)	Rated
		(3rd motor)		current of
				inverter
	b013	1s t electronic thermal	00(reduced characteristic)/ 01(constant torque characteristic)/	01/01/00
		characteristic selection	02(free setting)
thermal
	b213	2nd electronic thermal	00(reduced characteristic)/ 01(constant torque characteristic)/	01/01/00
		characteristic selection	02(free setting)
	b313	3rd electronic thermal	00/(reduced characteristic)01(constant torque characteristic)/	01/01/00
Electronic		characteristic selection	02(free setting)
	b015	Free electronic thermal	0.-400.(Hz)	0.
		frequency 1
	b016	Free electronic thermal	0.0-1000.(A)	0.0
		current 1
	b017	Free electronic thermal	0.-400.(Hz)	0.
		frequency 2
	b018	Free electronic thermal	0.0-1000. (A)	0.0
		current 2
	b019	Free electronic thermal	0.-400.(Hz)	0.
		frequency 3
	b020	Free electronic thermal	0.0-1000.(A)	0.0
		current 3
	b021	Overload restriction selection	00(invalid)/01(enabled on acceleration / constant speed)/	01
			02(enabled on constant speed)/03(enabled on acceleration / constant
			speed (speed increasing at regenerating mode))
	b022	Overload restriction level	0.50* rated current-2.00* rated current(A) <-1.80*ratede current(A)>	Rated current
				of Inverter
				x 1.50
	b023	Overload restriction limit	0.10-30.00(s)	1.00
		constant
limit	b024	Overload restriction 2	00(invalid)/01(enabled on acceleration / constant speed)/	01
			02(enabled on constant speed)/03(enabled on acceleration / constant
		selection
Overload			speed (speed increasing at regenerating mode))	x1.50
	b025	Overload restriction level 2	0.50*rated current-2.00*rated current(A) <-1.80*rated current(A)>	Rated current
				of inverter
	b026	Overload restriction constant	0.10-30.00(s)	1.00
		2
			00(impossible to change the data except this item when SFT terminal is
			ON)/01(impossible to change the data except setting frequency item
	b031	Software lock mode selection	when SFT terminal is ON)/02(impossible to change the data except this	01
			item)/
			03(impossible to change the data except setting frequency item)/
			10(possible to change data on operating)
	b100	Free V/f frequency 1	0.- Free V/f frequency2(Hz)	0.
	b101	Free V/f voltage 1	0.-800.0(V)	0.0
	b102	Free V/f frequency 2	0.- Free V/f frequency3(Hz)	0.
	b103	Free V/f voltage 2	0.-800.0(V)	0.0
	b104	Free V/f frequency 3	0.- Free V/f frequency4(Hz)	0.
setting	b105	Free V/f voltage 3	0.-800.0(V)	0.0
	b107	Free V/f voltage 4	0.-800.0(V)	0.0
	b106	Free V/f frequency 4	0.- Free V/f frequency5(Hz)	0.
V/f
	b108	Free V/f frequency 5	0.- Free V/f frequency6(Hz)	0.
Free	b109	Free V/f voltage 5	0.-800.0(V)	0.0
	b110	Free V/f frequency 6	0.- Free V/f frequency7(Hz)	0.
	b111	Free V/f voltage 6	0.-800.0(V)	0.0
	b112	Free V/f frequency 7	0.-400.(Hz)	0.
	b113	Free V/f voltage 7	0.-800.0(V)	0.0
	C001	Intelligent input 1 setting	01/(RV:Reverse is valid)/02(CF1:Multi-speed1)/ 03(CF2:Multi-speed2)/	18
			04(CF3:Multi-speed3)/ 05(CF4:Multi-speed4)/ 06(JG:Jogging)/
setting	C002	Intelligent input 2 setting		16
			07( DB:External DC braking)/ 08(SET:2nd control)/
			09(2CH:two-stage adjustable speed)/ 11( FRS:Free-run)/ 12( EXT:External trip)/
terminal			13( USP:Unattended start protection)/ 14(CS:commercial change)/
			15(SFT:software lock)/ 16(AT:Analog input voltage/current select)/
	C003	Intelligent input 3 setting	17(SET3:3rdcontrol)/ 18(RS:Reset inverter)/ 20(STA:3wire run)/	06
input			21(STP:3wire keep)/ 22(F/R:3wire forward/reverse)/
			23(PID:PID selection valid/invalid)/ 24(PIDC:PID integrating reset)/
	C004	Intelligent input 4 setting		11
Intelligent			26( CAS:Control gain switch function)/ 27( UP:Remote control UP function)/
			28( DWN:Remote control DOWN function)/29( UDC:Remote control data clear)/
			31( OPE:Operating by operator select)/ 32(SF1:Multi-speed bit1)/
	C005	Intelligent input 5 setting		09
			33(SF2:Multi-speed bit2)/ 34(SF3:Multi-speed bit3)/ 35(SF4:Multi-speed bit4)/
			36(SF5:Multi speed bit5)/ 37(SF6:Multi-speed bit6)/ 38(SF7:Multi-speed bit7)/
	C006	Intelligent input 6 setting		03/13/03
			39( OLR:Overload restriction change) / 40(TL:Torque limit select)/
			41(TRQ1:Torque limit switch 1)/ 42(TRQ2:Torque limit switch 2)/
	C007	Intelligent input 7 setting		02
			43((PPI:P/PI switch)/ 44(BOK:Braking comformation)/ 45( ORT:Orientation)/
			46(LAC:LAD cancel)/ 47(PCLR:Position error clear)/
	C008	Intelligent input 8 setting		01
			48(STAT:Permission of pulse train)/ no(NO:No assign)

(Note) < > indicate the setting range of 75 to 150kW

1- 5