Hitachi L300P Series service manual Meter C083 O2 adjustment 9999./1000-655310000-65530

Function Mode

	Code	Function name					L300P Setting range	Initial data	N o t e
								-FE/-FU/-FR
	C070	Data command					02(operator)/03(RS485)/04(option1)/05(option2)	02
ation	C071	Communicating					02(loop-back test)/03(2400bps)/04(4800bps)/	04
		transmission speed					05(9600bps)/06(19200bps)
Communic function	C072	Communication code					1. - 32.	1.
	C073	Communication bit					7(7bit)/8(8bit)	7
	C074	Communication parity					00(no parity name)/01(even parity)/02(odd parity)	00
	C075	Communication stop bit					1(bit)/2(bit)	1
	C078	Communication waiting					0.-1000.(ms)	0.
		time
setting	C082	OI adjustment					0.-9999./1000-6553(10000-65530)	Setting on
								forwarding
	C081	O adjustment					0.-9999./1000-6553(10000-65530)	forwarding
								Setting on
meter	C083	O2 adjustment					0.-9999./1000-6553(10000-65530)	Setting on
								forwarding
	C085	Thermistor adjustment					0.0 - 1000.	105.0
Analog	C088	AMI offset adjustment					0. - 20.0( mA)	4.0
	C086	AM offset adjustment					0.0 - 10.0(V)	0.0
	C087	AMI adjustment					0. - 255 .	80
	b034	RUN time/Power ON time					0.-9999./1000-6553(10000-65530)hr	0.
		level
	b035	Operation direction restrict					00(Reverse is valid)/01(Only forward)/02(Only reverse)	00
	b036	Start reduced voltage					00(Start reduced voltage time small)	06
							-06(Start reduced voltage time large)
	b037	Display selection					00(all display)/01(each function display)/	00
							02(User setting / main setting)
	b080	AM adjustment					0. - 255.	180
	b081	FM adjustment					0. - 255.	60
	b082	Start frequency adjustment					0.10-9.99(Hz)	0.50
	b083	Carrier frequency setting					0.5-12.0(kHz) Derating enable, <0.5-8.0kHz>	3.0
	b084	Initialize mode					00(Trip history clear)/01(Data initialization)/	00
							02(Trip history clear + data initialization)
	b085	Country code for					00(Interior)/01(EC)/02(USA)	01/02/00
		initialization
	b086	Frequency scalar					0.1-99.9	1.0
		conversion factor
	b087	STOP key enable					00(valid)/01(invalid)	00
	b088	Resume on FRS					00(0Hz start)/01(Start f-equaling)	00
		cancellation mode
	b090	BRD usage ratio					0.0-100.0(%)	0.0
	b091	Stop mode selection					00(deceleration stop)/01(Free-run stop)	00
	b092	Cooling fan control					00(Always ON)/01(ON during run, After power ON, then for 5 minutes	00
							on stop is implied.)
	b095	BRD selection					00(invalid)/01(valid<invalid during stop>)/	00
							02(valid<valid during stop>)
	b096	BRD ON level					330-380/660-760(V)	360/720
	b098	Thermistor selection					00(invalid)/01(Positive temperature coefficient enable)/	00
							02 (NTC enable)
	b099	Thermistor error level					0. – 9999. ( ohm)	3000.
	C061	Thermal warning level					0. – 100. ( %)	80
	C091	Debug mode selection					00(No display)/01(Display)	00
	C101	UP/DWN selection					00(No frequency data)/01(Keep frequency data)	00
others	C102	Reset f frequency matching					00(Trip cancel during ON)/01(Trip cancel during OFF)/	00
		Reset selection					02(Valid only during trip<Cancel during ON>)
The	C103	selection					00(0H z start)/01(Start f-equaling)	00
	C121	O zero adjustment					0.-9999./1000-6553(10000-65530)	Set on
								forwarding
	C122	OI zero adjustment					0.-9999./1000-6553(10000-65530)	Set on
								forwarding
	C123	O2 zero adjustment					0.-9999./1000-6553(10000-65530)	Set on
								forwarding
	H003	1s t allowable motor					0.20-90.0(kW) <0.20-160(kW)>	Set on
		selection						forwarding
	H203	2nd allowable motor					0.20-90.0(kW) <0.20-160(kW)>	Set on
		selection						forwarding
	H004	1s t motor pole selection					2/4/6/8(pole)	4
	H204	2nd motor pole selection					2/4/6/8(pole)	4
	H006	1s t stabilized factor					0. - 255.	100.
	H206	2nd stabilized factor					0. - 255.	100.
	P001	Option1 operation selection					00(TRP)/01(RUN)	00
		on error
	P002	Option2 operation selection					00(TRP)/01(RUN)	00
		on error
	P031	Digital	input option			input	00(operation)/01(option1)/02(option2)	00
		mode selection(Acc/Dec)
	P044	DeviceNet running order of					0.00-99.99s	1.00
		monitoring timer setting
	P045	Setting	in	action		of	00(trip)/01(trip after deceleration stop)/02(invalid)/	0.
		abnormal communication					03(free-run)04(deceleration stop)
	P046	Output	assemble		instance		20,21,100	21
		Number setting
	P047	Input	assemble		instance		70,71,101	71
		Number setting
	P048	Detect	of idol	mode		for	00(trip)/01(trip after deceleration stop)/02(invalid)/	01
		motion setting					03(free-run)04(deceleration stop)
	P049	Pole setting		of	rotation		0-38(even only)	0
		speed

(Note) < > indicate the setting range of 90 to 132kW (Note1) P044-P049 are displayed o n a 0.4- 7 5kW model.

1- 14