Grizzly G0504 owner manual Grounding Converting to, Inside of electrical box

Page 12

Grounding

Converting to 440V

 

 

 

 

 

 

Electrocution or fire could result if this machine is not grounded correctly. Make sure all electrical cir- cuits are grounded before you connect them to the machine. DO NOT use the Model G0504 if it is not grounded.

In the event of an electrical malfunction or break- down, grounding provides a path of least resis- tance for electric current to reduce the risk of electric shock. This machine must be equipped with an electric cord that has an equipment grounding conductor. This conductor must be grounded in accordance with all local codes and ordinances.

Improper connections of the electrical-grounding conductor can result in the risk of electric shock. Check with a qualified electrician or one of our service personnel if the grounding instructions are not completely understood, or if you are in doubt as to whether the machine is properly grounded.

-10-

Converting the Model G0504 to 440V operation consists of 1) wiring the voltage transformer, 2) replacing the overload relays with those provided in the G0504 440V conversion kit, and 3) rewiring the main motor and the elevation motor. A quali- fied electrician must inspect all electrical modifi- cations before connecting to power.

Voltage Transformer

Main Motor Relay

Figure 3. Inside of electrical box.

To convert the Model G0504 to 440V:

1.Disconnect the resaw from the power source!

2.At the voltage transformer, move the T1 wire from the 220V terminal to the 440V terminal.

Figure 4. Location on voltage transformer to

move the T1 wire for 440V operation. G0504 16" Horizontal Resaw Bandsaw

Image 12
Contents Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Service Adjustments PartsGeneral Information CommentaryMachine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Phase Power Circuit RequirementsGrounding Converting to Inside of electrical boxMain motor 440V wiring Machine Features Main FeaturesPage Memory Preset Keys A, B, C, D-Allows Control PanelSET UP About this SectionPiece Inventory UnpackingHardware Recognition Chart Clean Up Site Considerations Removing Resaw from Crate Pallet Mounting Resaw to the FloorInstalling Tensioning Blade To install and tension the bladeAdjusting Blade Guides Always de-tension blade after useTo adjust the upper guide block Support Bearing To adjust the support bearingsConnecting to Dust Power SourceTo connect the resaw to a dust collector Power on switch Test RunOperation Safety Conveyor Controls OperationsTo operate the infeed conveyor Setting Blade Height Calibrating Digital DisplayTo set the blade height with the keypad To calibrate the digital displaySetting Memory Using Memory Button To store a height in the a memory preset keyTo use the stored memory preset in the a key To set the memory functionResawing To perform a resawing operationBlade Information Accessories H4959-Coolant DispenserH0580-Pneumatic Grease Gun H1300 H1298 G7984 H2347 H0736Maintenance CleaningMiscellaneous BeltsGrease Fittings Hydraulic System Minor Service Check the hydraulic fluid level dailyHydraulic System Major Service To inspect the hydraulic fluidTo clean the tank screen To clean the bottom of the tankTo fill the tank with new fluid Service Adjustments About ServiceAdjusting Lower Blade Guides Adjusting V-Belt Tension To adjust the tension for the hydraulic pump V-beltAdjusting Main Conveyor Table Replacing V-BeltsTo check the main conveyor table alignment Tracking Conveyors To set the conveyor trackingReplacing Conveyors To replace the conveyor beltsDisconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Troubleshooting UnderpoweredSymptom Possible Cause Possible Solution Housing Parts PartsHousing Parts List DescriptionFrame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Hydraulic System Parts List Connector 3/8H X 3/8HElectrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page