Grizzly G0504 owner manual Resawing, To perform a resawing operation

Page 29

Resawing

To perform a resawing operation:

1.Make sure the blade is installed and ten- sioned correctly. See “Installing Blade” on Page 19 for more information.

2.Make sure the blade is tracking correctly. See “Adjusting Blade Guides” on Page 20 for more information.

3.Turn the control panel POWER ON switch clockwise to supply power to the machine.

4.Set the blade height at the control panel. See “Setting Blade Height” on Page 25. Note—The accuracy of the blade height shown on the digital display can only be assured if the calibration process has been performed. See Page 25 for more informa- tion on calibrating the digital display.

5.Press the MOTOR START button to start the bandsaw blade.

6.Push the infeed conveyor engagement lever forward to start the infeed conveyor. Turn the infeed conveyor speed dial counter- clockwise to increase the speed and clock- wise to decrease the speed. See “Conveyor Controls” on Page 24 for more information.

7.Recheck the blade tension.

8.Make sure the workpiece has two sides that are relatively flat and parallel with each other.

9.Begin feeding the workpiece under the front pressure rollers with the jointed edge against the guide rollers, as shown in Figure 23.

Guide Rollers

Front Pressure

Roller Assembly

Figure 23. Feeding the workpiece through the

bandsaw.

10.Watch the load meter (Figure 24) at the top of the control panel. The meter displays the amperage load that is being placed on the machine. Adjust the infeed conveyor feed rate until the meter reads between 25-30 Amps during the cutting operation.

Figure 24. Load meter.

11.Receive the workpiece on the outfeed side of the machine. Note—If a second person is receiving the workpieces, use the return conveyor to send them back to the person on the infeed side.

NOTICE Always de-tension blade after use.

G0504 16" Horizontal Resaw Bandsaw

-27-

Image 29

Contents Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Parts Service AdjustmentsCommentary General InformationMachine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Circuit Requirements Phase PowerInside of electrical box Grounding Converting toMain motor 440V wiring Main Features Machine FeaturesPage Control Panel Memory Preset Keys A, B, C, D-AllowsAbout this Section SET UPPiece Inventory UnpackingHardware Recognition Chart Clean Up Site Considerations Mounting Resaw to the Floor Removing Resaw from Crate PalletTo install and tension the blade Installing Tensioning BladeAlways de-tension blade after use Adjusting Blade GuidesTo adjust the support bearings To adjust the upper guide block Support BearingTo connect the resaw to a dust collector Connecting to DustPower Source Test Run Power on switchTo operate the infeed conveyor Operation Safety Conveyor ControlsOperations Calibrating Digital Display Setting Blade HeightTo set the blade height with the keypad To calibrate the digital displayTo store a height in the a memory preset key Setting Memory Using Memory ButtonTo use the stored memory preset in the a key To set the memory functionTo perform a resawing operation ResawingBlade Information H4959-Coolant Dispenser AccessoriesH0580-Pneumatic Grease Gun H1300 H1298 G7984 H2347 H0736Cleaning MaintenanceMiscellaneous BeltsGrease Fittings Check the hydraulic fluid level daily Hydraulic System Minor ServiceTo inspect the hydraulic fluid Hydraulic System Major ServiceTo fill the tank with new fluid To clean the tank screenTo clean the bottom of the tank Adjusting Lower Blade Guides Service AdjustmentsAbout Service To adjust the tension for the hydraulic pump V-belt Adjusting V-Belt TensionTo check the main conveyor table alignment Adjusting Main Conveyor TableReplacing V-Belts To set the conveyor tracking Tracking ConveyorsTo replace the conveyor belts Replacing ConveyorsDisconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Underpowered TroubleshootingSymptom Possible Cause Possible Solution Parts Housing PartsDescription Housing Parts ListFrame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Connector 3/8H X 3/8H Hydraulic System Parts ListElectrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page