Grizzly G0504 owner manual Table of Contents

Page 3

Table of Contents
SECTION 1: GENERAL INFORMATION	3
Commentary	3
Machine Data Sheet	4
SECTION 2: SAFETY	5
Additional Safety Instructions for Bandsaws	7
Additional Safety Instructions for Hydraulics	8
SECTION 3: CIRCUIT REQUIREMENTS	9
3-Phase Power	9
Grounding	10
Converting to 440V	10
SECTION 4: MACHINE FEATURES	12
Main Features	12
Control Panel	14
SECTION 5: SET UP	15
About this Section	15
Unpacking	15
Piece Inventory	15
Hardware Recognition Chart	16
Clean Up	17
Site Considerations	17
Removing Resaw from Crate Pallet	18
Mounting Resaw to the Floor	18
Installing & Tensioning Blade	19
Adjusting Blade Guides	20
Connecting to Dust Collector	22
Connecting to Power Source	22
Test Run	23
SECTION 6: OPERATIONS	24
Operation Safety	24
Conveyor Controls	24
Setting Blade Height	25
Calibrating Digital Display	25
Setting Memory Button	26
Using Memory Preset Keys	26
Resawing	27
Blade Information	28
Accessories	29
SECTION 7: MAINTENANCE	30
Cleaning	30
Miscellaneous	30
V-Belts	30
Bearings	30
Grease Fittings	31
Hydraulic Fluid Schedule	32
Hydraulic System Minor Service	32
Hydraulic System Major Service	33

Image 3

Contents Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Parts Service AdjustmentsCommentary General InformationMachine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Circuit Requirements Phase PowerInside of electrical box Grounding Converting toMain motor 440V wiring Main Features Machine FeaturesPage Control Panel Memory Preset Keys A, B, C, D-AllowsUnpacking SET UPAbout this Section Piece InventoryHardware Recognition Chart Clean Up Site Considerations Mounting Resaw to the Floor Removing Resaw from Crate PalletTo install and tension the blade Installing Tensioning BladeAlways de-tension blade after use Adjusting Blade GuidesTo adjust the support bearings To adjust the upper guide block Support BearingConnecting to Dust Power SourceTo connect the resaw to a dust collector Test Run Power on switchOperation Safety Conveyor Controls OperationsTo operate the infeed conveyor To calibrate the digital display Setting Blade HeightCalibrating Digital Display To set the blade height with the keypadTo set the memory function Setting Memory Using Memory ButtonTo store a height in the a memory preset key To use the stored memory preset in the a keyTo perform a resawing operation ResawingBlade Information H1300 H1298 G7984 H2347 H0736 AccessoriesH4959-Coolant Dispenser H0580-Pneumatic Grease GunBelts MaintenanceCleaning MiscellaneousGrease Fittings Check the hydraulic fluid level daily Hydraulic System Minor ServiceTo inspect the hydraulic fluid Hydraulic System Major ServiceTo clean the tank screen To clean the bottom of the tankTo fill the tank with new fluid Service Adjustments About ServiceAdjusting Lower Blade Guides To adjust the tension for the hydraulic pump V-belt Adjusting V-Belt TensionAdjusting Main Conveyor Table Replacing V-BeltsTo check the main conveyor table alignment To set the conveyor tracking Tracking ConveyorsTo replace the conveyor belts Replacing ConveyorsDisconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Underpowered TroubleshootingSymptom Possible Cause Possible Solution Parts Housing PartsDescription Housing Parts ListFrame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Connector 3/8H X 3/8H Hydraulic System Parts ListElectrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page