Grizzly G0504 owner manual Machine Features, Main Features

Page 14

SECTION 4: MACHINE FEATURES

1

2

6

5

4

3

Figure 7. Main view of machine features and controls.

Main Features

1.Infeed Pressure Rollers—Maintain down- ward pressure on the board to keep it sturdy during cutting.

2.Head Elevation Motor—Responsible for moving the head (the part of the saw that contains the wheels and blade) up or down as needed.

3.Electrical Control Box—Main area for wir- ing, rewiring, and changing the fuses. Should never be opened when the machine is con- nected to the power source!

4.Infeed Conveyor—Moves the board through the bandsaw blade during cutting.

5.Infeed Conveyor Engagement Lever— Allows the operator to stop and start the infeed conveyor while the blade is moving.

6.Control Panel—The part of the resaw where the operator can control the starting and stopping of the motor, the various height changes, and the calibration of the blade height to the conveyor. The control panel also houses a load meter that allows the operator to monitor the load being placed on the resaw during operation. For more details, see Page 14.

-12-	G0504 16" Horizontal Resaw Bandsaw

Image 14

Contents Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Service Adjustments PartsGeneral Information CommentaryMachine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Phase Power Circuit RequirementsGrounding Converting to Inside of electrical boxMain motor 440V wiring Machine Features Main FeaturesPage Memory Preset Keys A, B, C, D-Allows Control PanelPiece Inventory SET UPAbout this Section UnpackingHardware Recognition Chart Clean Up Site Considerations Removing Resaw from Crate Pallet Mounting Resaw to the FloorInstalling Tensioning Blade To install and tension the bladeAdjusting Blade Guides Always de-tension blade after useTo adjust the upper guide block Support Bearing To adjust the support bearingsTo connect the resaw to a dust collector Connecting to DustPower Source Power on switch Test RunTo operate the infeed conveyor Operation Safety Conveyor ControlsOperations To set the blade height with the keypad Setting Blade HeightCalibrating Digital Display To calibrate the digital displayTo use the stored memory preset in the a key Setting Memory Using Memory ButtonTo store a height in the a memory preset key To set the memory functionResawing To perform a resawing operationBlade Information H0580-Pneumatic Grease Gun AccessoriesH4959-Coolant Dispenser H1300 H1298 G7984 H2347 H0736Miscellaneous MaintenanceCleaning BeltsGrease Fittings Hydraulic System Minor Service Check the hydraulic fluid level dailyHydraulic System Major Service To inspect the hydraulic fluidTo fill the tank with new fluid To clean the tank screenTo clean the bottom of the tank Adjusting Lower Blade Guides Service AdjustmentsAbout Service Adjusting V-Belt Tension To adjust the tension for the hydraulic pump V-beltTo check the main conveyor table alignment Adjusting Main Conveyor TableReplacing V-Belts Tracking Conveyors To set the conveyor trackingReplacing Conveyors To replace the conveyor beltsDisconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Troubleshooting UnderpoweredSymptom Possible Cause Possible Solution Housing Parts PartsHousing Parts List DescriptionFrame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Hydraulic System Parts List Connector 3/8H X 3/8HElectrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page