Grizzly G0504 owner manual Main Conveyor Table Parts List

Page 61

Main Conveyor Table Parts List

REF	PART #	DESCRIPTION

1801	PLN05M	LOCK NUT M10-1.5
1802	PW04M	FLAT WASHER 10MM
1803	P0504603	CONVEYOR LOWER PLATE
1804	PN33M	HEX NUT M24-2
1805	P0504605	ADJUSTMENT BOLT
1806	PB01M	HEX BOLT M10-1.5 X 30
1807	PLW06M	LOCK WASHER 10MM
1808	P0504609	ROLLER SEAT
1809	P0504610	ROLLER
1810	P0504611B	ROLLER PLATE (REAR)
1811	PB33M	HEX BOLT M12-1.75 X 50
1812	PLW05M	LOCK WASHER 12MM
1813	PW06M	FLAT WASHER 12MM
1814	P05041814	HYDRAULIC MOTOR OMP250
1815	P0504618A	MOTOR BEARING SEAT
1816	P6008LLB	BALL BEARING 6008LLB
1817	PK13	KEY 1/4 X 1/4 X 1-1/2
1818	P0504621	REAR ROLLER BRACKET R
1819	P0504622	REAR ROLLER
1820	P0504623	CONVEYOR BELT 400
1821	P0504624	REAR ROLLER BRACKET L
1822	P0504625	FLANGE BEARING UCFL205
1823	PB25M	HEX BOLT M12-1.75 X 25
1824	P0504636	CONVEYOR PLATEN
1825	PCB09M	CARRIAGE BOLT M10-1.5 X 25
1826	PB01M	HEX BOLT M10-1.5 X 30
1827	P0504637	ADJUSTMENT SCREW
1828	PN02M	HEX NUT M10-1.5
1829	PB32M	HEX BOLT M10-1.5 X 25
1830	P0504649	FRONT ROLLER SUPPORT
1831	P0504650	FRONT ROLLER
1832	P0504611A	ROLLER PLATE (FRONT)

G0504 16" Horizontal Resaw Bandsaw

-59-

Image 61

Contents Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Parts Service AdjustmentsCommentary General InformationMachine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Circuit Requirements Phase PowerInside of electrical box Grounding Converting toMain motor 440V wiring Main Features Machine FeaturesPage Control Panel Memory Preset Keys A, B, C, D-AllowsAbout this Section SET UPPiece Inventory UnpackingHardware Recognition Chart Clean Up Site Considerations Mounting Resaw to the Floor Removing Resaw from Crate PalletTo install and tension the blade Installing Tensioning BladeAlways de-tension blade after use Adjusting Blade GuidesTo adjust the support bearings To adjust the upper guide block Support BearingPower Source Connecting to DustTo connect the resaw to a dust collector Test Run Power on switchOperations Operation Safety Conveyor ControlsTo operate the infeed conveyor Calibrating Digital Display Setting Blade HeightTo set the blade height with the keypad To calibrate the digital displayTo store a height in the a memory preset key Setting Memory Using Memory ButtonTo use the stored memory preset in the a key To set the memory functionTo perform a resawing operation ResawingBlade Information H4959-Coolant Dispenser AccessoriesH0580-Pneumatic Grease Gun H1300 H1298 G7984 H2347 H0736Cleaning MaintenanceMiscellaneous BeltsGrease Fittings Check the hydraulic fluid level daily Hydraulic System Minor ServiceTo inspect the hydraulic fluid Hydraulic System Major ServiceTo clean the bottom of the tank To clean the tank screenTo fill the tank with new fluid About Service Service AdjustmentsAdjusting Lower Blade Guides To adjust the tension for the hydraulic pump V-belt Adjusting V-Belt TensionReplacing V-Belts Adjusting Main Conveyor TableTo check the main conveyor table alignment To set the conveyor tracking Tracking ConveyorsTo replace the conveyor belts Replacing ConveyorsDisconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Underpowered TroubleshootingSymptom Possible Cause Possible Solution Parts Housing PartsDescription Housing Parts ListFrame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Connector 3/8H X 3/8H Hydraulic System Parts ListElectrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page