Grizzly G0504 owner manual Main motor 440V wiring

Page 13

3.Remove the wiring box covers on the main motor and elevation motor.

4.Wire the main motor and elevation motor as shown on the diagrams on the inside of each motor wiring box cover. (The circled refer- ences on the diagrams represent labels on the wires.)

Note: Figures 5 & 6 below have been pro- vided for your reference and are current at the time that this manual was written. However, always use the diagram on the wire cover that comes with your motor! Also, the electrical system on this machine is setup for the "RUN" diagrams shown on the wire cover. Ignore the "START" diagrams for this machine.

��

��

��

��

��

5.Replace the main motor relay (LR3D-3359 48/65A) with the relay from kit (LR3D-3355 30/40A) and set the dial to “33.”

6.Replace any wire duct covers and motor wir- ing box covers you might have removed dur- ing this procedure, and close the electrical box door.

To avoid electrocution or fire, ensure all wiring mod- ifications are inspected and approved by a quali- fied electrician before con- necting the machine to the power source.

Figure 5. Main motor 440V wiring.

��

��

��

��

��

Figure 6. Elevation motor 440V wiring.

G0504 16" Horizontal Resaw Bandsaw

-11-

Image 13

Contents Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Parts Service AdjustmentsCommentary General InformationMachine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Circuit Requirements Phase PowerInside of electrical box Grounding Converting toMain motor 440V wiring Main Features Machine FeaturesPage Control Panel Memory Preset Keys A, B, C, D-AllowsAbout this Section SET UPPiece Inventory UnpackingHardware Recognition Chart Clean Up Site Considerations Mounting Resaw to the Floor Removing Resaw from Crate PalletTo install and tension the blade Installing Tensioning BladeAlways de-tension blade after use Adjusting Blade GuidesTo adjust the support bearings To adjust the upper guide block Support BearingPower Source Connecting to DustTo connect the resaw to a dust collector Test Run Power on switchOperations Operation Safety Conveyor ControlsTo operate the infeed conveyor Calibrating Digital Display Setting Blade HeightTo set the blade height with the keypad To calibrate the digital displayTo store a height in the a memory preset key Setting Memory Using Memory ButtonTo use the stored memory preset in the a key To set the memory functionTo perform a resawing operation ResawingBlade Information H4959-Coolant Dispenser AccessoriesH0580-Pneumatic Grease Gun H1300 H1298 G7984 H2347 H0736Cleaning MaintenanceMiscellaneous BeltsGrease Fittings Check the hydraulic fluid level daily Hydraulic System Minor ServiceTo inspect the hydraulic fluid Hydraulic System Major ServiceTo clean the bottom of the tank To clean the tank screenTo fill the tank with new fluid About Service Service AdjustmentsAdjusting Lower Blade Guides To adjust the tension for the hydraulic pump V-belt Adjusting V-Belt TensionReplacing V-Belts Adjusting Main Conveyor TableTo check the main conveyor table alignment To set the conveyor tracking Tracking ConveyorsTo replace the conveyor belts Replacing ConveyorsDisconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Underpowered TroubleshootingSymptom Possible Cause Possible Solution Parts Housing PartsDescription Housing Parts ListFrame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Connector 3/8H X 3/8H Hydraulic System Parts ListElectrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page