Grizzly G0504 owner manual Removing Resaw from Crate Pallet, Mounting Resaw to the Floor

Page 20

Removing Resaw from Crate Pallet

The Model G0504 is a heavy machine that weighs approximately 3300 lbs. Serious per- sonal injury may occur if safe moving methods are not followed. To be safe, you will need assistance and power equipment when moving the ship- ping crate and remov- ing the machine from the crate.

To remove the resaw from the crate pallet:

1.Remove the lag bolts from the stand feet that secure the resaw to the crate pallet.

2.Using a forklift, lift the resaw from the frame location shown in Figure 11, and move it to your predetermined location.

Mounting Resaw to the Floor

Although not required, we recommend that you mount your new machine to the floor. Because this is an optional step and floor materials may vary, floor mounting hardware is not included.

Bolting to Concrete Floors

Lag shield anchors with lag bolts and anchor studs (Figure 12) are two popular methods for anchoring an object to a concrete floor. We sug- gest you research the many options and methods for mounting your machine and choose the best that fits your specific application.

NOTICE Anchor studs are stronger and more per- manent alternatives to lag shield anchors; however, they will stick out of the floor, which may cause a tripping hazard if you decide to move your machine.

Figure 11. Lifting points for moving the resaw

with a forklift.

Figure 12. Typical fasteners for mounting to concrete floors.

-18-

G0504 16" Horizontal Resaw Bandsaw

Image 20
Contents Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Service Adjustments PartsGeneral Information CommentaryMachine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Phase Power Circuit RequirementsGrounding Converting to Inside of electrical boxMain motor 440V wiring Machine Features Main FeaturesPage Memory Preset Keys A, B, C, D-Allows Control PanelSET UP About this SectionPiece Inventory UnpackingHardware Recognition Chart Clean Up Site Considerations Removing Resaw from Crate Pallet Mounting Resaw to the FloorInstalling Tensioning Blade To install and tension the bladeAdjusting Blade Guides Always de-tension blade after useTo adjust the upper guide block Support Bearing To adjust the support bearingsTo connect the resaw to a dust collector Connecting to DustPower Source Power on switch Test RunTo operate the infeed conveyor Operation Safety Conveyor ControlsOperations Setting Blade Height Calibrating Digital DisplayTo set the blade height with the keypad To calibrate the digital displaySetting Memory Using Memory Button To store a height in the a memory preset keyTo use the stored memory preset in the a key To set the memory functionResawing To perform a resawing operationBlade Information Accessories H4959-Coolant DispenserH0580-Pneumatic Grease Gun H1300 H1298 G7984 H2347 H0736Maintenance CleaningMiscellaneous BeltsGrease Fittings Hydraulic System Minor Service Check the hydraulic fluid level dailyHydraulic System Major Service To inspect the hydraulic fluidTo fill the tank with new fluid To clean the tank screenTo clean the bottom of the tank Adjusting Lower Blade Guides Service AdjustmentsAbout Service Adjusting V-Belt Tension To adjust the tension for the hydraulic pump V-beltTo check the main conveyor table alignment Adjusting Main Conveyor TableReplacing V-Belts Tracking Conveyors To set the conveyor trackingReplacing Conveyors To replace the conveyor beltsDisconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Troubleshooting UnderpoweredSymptom Possible Cause Possible Solution Housing Parts PartsHousing Parts List DescriptionFrame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Hydraulic System Parts List Connector 3/8H X 3/8HElectrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page