Grizzly G0504 owner manual Front Hold Down Parts List

Page 65

Front Hold Down Parts List

REF	PART #	DESCRIPTION

2101	PN09M	HEX NUT M12-1.75
2102	PLW05M	LOCK WASHER 12MM
2103	PW06M	FLAT WASHER 12MM
2104	P0504625	FLANGE BEARING UCFL205
2105	P0504721	PRESSURE ROLLER SUPPORT (L)
2106	P0504727	UPPER SHAFT
2107	PB32M	HEX BOLT M10-1.5 X 25
2108	PLW06M	LOCK WASHER 10MM
2109	PW04M	FLAT WASHER 10MM
2110	PB49M	HEX BOLT M12-1.75 X 20
2111	P0504747	PRESSURE ROLLER WHEEL
2112	P0504748	COLLAR
2113	P0504749	FRONT ROLLER SHAFT
2114	P0504742	FRONT PRESSURE PLATE
2115	PB01M	HEX BOLT M10-1.5 X 30
2116	P0504731	PRESSURE ROLLER SUPPORT (R)
2117	PN02M	HEX NUT M10-1.5
2118	P0504716	COLLAR
2119	P0504709	SHOCK ABSORBER
2120	PSB101M	CAP SCREW M12-1.75 X 90
2121	P0504713	IRON PLATE
2122	PSB63M	CAP SCREW M12-1.75 X 60

G0504 16" Horizontal Resaw Bandsaw

-63-

Image 65

Contents Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Parts Service AdjustmentsCommentary General InformationMachine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Circuit Requirements Phase PowerInside of electrical box Grounding Converting toMain motor 440V wiring Main Features Machine FeaturesPage Control Panel Memory Preset Keys A, B, C, D-AllowsAbout this Section SET UPPiece Inventory UnpackingHardware Recognition Chart Clean Up Site Considerations Mounting Resaw to the Floor Removing Resaw from Crate PalletTo install and tension the blade Installing Tensioning BladeAlways de-tension blade after use Adjusting Blade GuidesTo adjust the support bearings To adjust the upper guide block Support BearingTo connect the resaw to a dust collector Connecting to DustPower Source Test Run Power on switchTo operate the infeed conveyor Operation Safety Conveyor ControlsOperations Calibrating Digital Display Setting Blade HeightTo set the blade height with the keypad To calibrate the digital displayTo store a height in the a memory preset key Setting Memory Using Memory ButtonTo use the stored memory preset in the a key To set the memory functionTo perform a resawing operation ResawingBlade Information H4959-Coolant Dispenser AccessoriesH0580-Pneumatic Grease Gun H1300 H1298 G7984 H2347 H0736Cleaning MaintenanceMiscellaneous BeltsGrease Fittings Check the hydraulic fluid level daily Hydraulic System Minor ServiceTo inspect the hydraulic fluid Hydraulic System Major ServiceTo fill the tank with new fluid To clean the tank screenTo clean the bottom of the tank Adjusting Lower Blade Guides Service AdjustmentsAbout Service To adjust the tension for the hydraulic pump V-belt Adjusting V-Belt TensionTo check the main conveyor table alignment Adjusting Main Conveyor TableReplacing V-Belts To set the conveyor tracking Tracking ConveyorsTo replace the conveyor belts Replacing ConveyorsDisconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Underpowered TroubleshootingSymptom Possible Cause Possible Solution Parts Housing PartsDescription Housing Parts ListFrame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Connector 3/8H X 3/8H Hydraulic System Parts ListElectrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page