Grizzly G0504 owner manual Drive Wheel Parts

Page 58

Drive Wheel Parts

��

��

��

��

��

��

��

��

��

��		��	��
		��
	��
��	��
	��		��	��
			��	��
			��	��
			��	��
				��
	��
	��
��				��
��
				��
			��	��
			��	��
			��	��
			��
			��
		��
	��

REF	PART #	DESCRIPTION

1601	P0504428A	LOCK NUT AN11
1602	PTLW08M	EXT TOOTH WASHER 10MM
1603	P0504429A	LOCK RING
1604	PSB73M	CAP SCREW M12-1.75 X 50
1605	PLW05M	LOCK WASHER 12MM
1606	P0504403	RIGHT BLADE WHEEL
1607	P0504455	INT RETAINING RING 90MM
1608	P0504456	OIL SEAL TC-70 X 90 X 8
1609	P32011	BEARING 32011
1610	P05041610	BEARING SEAT-LEFT

REF	PART #	DESCRIPTION

1611	P05041611	BELT 5V X 740
1612	P32012	TAPER ROLLER BEARING 32012
1613	P05041613	OIL SEAL TC-75 X 95 X 10
1614	P05041614	INT RETAINING RING 95MM
1615	PZERK2	GREASE FITTING PT 1/8
1616	P05041616	RIGHT WHEEL SHAFT
1617	PB25M	HEX BOLT M12-1.75 X 25
1618	PN09M	HEX NUT M12-1.75
1619	P05041619	WHEEL ADJUSTMENT PLATE

-56-	G0504 16" Horizontal Resaw Bandsaw

Image 58

Contents Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Service Adjustments PartsGeneral Information CommentaryMachine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Phase Power Circuit RequirementsGrounding Converting to Inside of electrical boxMain motor 440V wiring Machine Features Main FeaturesPage Memory Preset Keys A, B, C, D-Allows Control PanelPiece Inventory SET UPAbout this Section UnpackingHardware Recognition Chart Clean Up Site Considerations Removing Resaw from Crate Pallet Mounting Resaw to the FloorInstalling Tensioning Blade To install and tension the bladeAdjusting Blade Guides Always de-tension blade after useTo adjust the upper guide block Support Bearing To adjust the support bearingsPower Source Connecting to DustTo connect the resaw to a dust collector Power on switch Test RunOperations Operation Safety Conveyor ControlsTo operate the infeed conveyor To set the blade height with the keypad Setting Blade HeightCalibrating Digital Display To calibrate the digital displayTo use the stored memory preset in the a key Setting Memory Using Memory ButtonTo store a height in the a memory preset key To set the memory functionResawing To perform a resawing operationBlade Information H0580-Pneumatic Grease Gun AccessoriesH4959-Coolant Dispenser H1300 H1298 G7984 H2347 H0736Miscellaneous MaintenanceCleaning BeltsGrease Fittings Hydraulic System Minor Service Check the hydraulic fluid level dailyHydraulic System Major Service To inspect the hydraulic fluidTo clean the bottom of the tank To clean the tank screenTo fill the tank with new fluid About Service Service AdjustmentsAdjusting Lower Blade Guides Adjusting V-Belt Tension To adjust the tension for the hydraulic pump V-beltReplacing V-Belts Adjusting Main Conveyor TableTo check the main conveyor table alignment Tracking Conveyors To set the conveyor trackingReplacing Conveyors To replace the conveyor beltsDisconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Troubleshooting UnderpoweredSymptom Possible Cause Possible Solution Housing Parts PartsHousing Parts List DescriptionFrame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Hydraulic System Parts List Connector 3/8H X 3/8HElectrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page