Grizzly G0504 owner manual Set Up, About this Section, Piece Inventory, Unpacking

Page 17

SECTION 5: SET UP

About this Section

The purpose of this section is to guide you through the required steps to get your machine out of its crate and into operating condition.

This machine presents serious injury hazards to untrained users. Read through this entire man- ual to become familiar with the controls and operations before start- ing the machine!

Wear safety glasses during the entire set up process!

Piece Inventory

After all the parts have been removed from the shipping crate, you should have:

•Resaw Bandsaw Machine

•Bandsaw Blade 180" x 1" x 0.035"

•Tool Box

•T-Handle Wrench 19mm

•7 pc. Combination Wrench Set —10, 12, 13, 14, 17, 19, 21 mm

•7 pc. Hex Wrench Set —2.5, 3, 4, 5, 6, 8, 10 mm

•Phillips Head Screwdriver

•Flat Head Screwdriver

•Adjustment Wrench 30 x 32 mm

In the event that any non-proprietary parts are missing (e.g. nuts or washers), we would be glad to replace them, or for the sake of expediency, replacements can be obtained at your local hard- ware store.

Unpacking

The Model G0504 is shipped from the manu- facturer in a carefully built crate. If you discover the machine is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice.

Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the con- dition of your shipment, you should inventory the equipment from the shipping crate.

Figure 10. Piece inventory from packing crate.

G0504 16" Horizontal Resaw Bandsaw

-15-

Image 17

Contents Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Parts Service AdjustmentsCommentary General InformationMachine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Circuit Requirements Phase PowerInside of electrical box Grounding Converting toMain motor 440V wiring Main Features Machine FeaturesPage Control Panel Memory Preset Keys A, B, C, D-AllowsAbout this Section SET UPPiece Inventory UnpackingHardware Recognition Chart Clean Up Site Considerations Mounting Resaw to the Floor Removing Resaw from Crate PalletTo install and tension the blade Installing Tensioning BladeAlways de-tension blade after use Adjusting Blade GuidesTo adjust the support bearings To adjust the upper guide block Support BearingTo connect the resaw to a dust collector Connecting to DustPower Source Test Run Power on switchTo operate the infeed conveyor Operation Safety Conveyor ControlsOperations Calibrating Digital Display Setting Blade HeightTo set the blade height with the keypad To calibrate the digital displayTo store a height in the a memory preset key Setting Memory Using Memory ButtonTo use the stored memory preset in the a key To set the memory functionTo perform a resawing operation ResawingBlade Information H4959-Coolant Dispenser AccessoriesH0580-Pneumatic Grease Gun H1300 H1298 G7984 H2347 H0736Cleaning MaintenanceMiscellaneous BeltsGrease Fittings Check the hydraulic fluid level daily Hydraulic System Minor ServiceTo inspect the hydraulic fluid Hydraulic System Major ServiceTo fill the tank with new fluid To clean the tank screenTo clean the bottom of the tank Adjusting Lower Blade Guides Service AdjustmentsAbout Service To adjust the tension for the hydraulic pump V-belt Adjusting V-Belt TensionTo check the main conveyor table alignment Adjusting Main Conveyor TableReplacing V-Belts To set the conveyor tracking Tracking ConveyorsTo replace the conveyor belts Replacing ConveyorsDisconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Underpowered TroubleshootingSymptom Possible Cause Possible Solution Parts Housing PartsDescription Housing Parts ListFrame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Connector 3/8H X 3/8H Hydraulic System Parts ListElectrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page