Grizzly G0504 Setting Blade Height, Calibrating Digital Display, To calibrate the digital display

Page 27

Setting Blade Height

The blade height is defined as the distance between the conveyor table and the bottom face of the bandsaw blade. There is an internal limit switch that will not allow the blade to be adjusted closer than 14" to the conveyor table. Note—Use the “Blade Memory Function” described in the next subsection when you want to make resaw cuts thinner than 14", and be sure to cut from the top of the workpiece.

The blade height can be adjusted by using the keypad, or by pressing the UP and DOWN con- trol panel buttons. After using either method of adjustment, the digital display will indicate the current blade height.

To set the blade height with the UP and DOWN control panel buttons:

1.Turn the control panel POWER ON switch clockwise to supply power to the control panel.

2.Press the UP button to move the blade up and press the DOWN button to move the blade down. Watch the digital display to gauge the blade height.

To set the blade height with the keypad:

1.Turn the control panel POWER ON switch clockwise to supply power to the control panel.

2.Press the FUNC key.

3.Enter the desired blade height to the nearest hundredth's place. For example, if you want the blade height to be 2", press 2, 0, 0 on the keypad. If you want the blade height to be 34", press 7, 5.

4.After the blade height has been entered, press the START key.

Calibrating Digital

Display

The digital display indicates the distance between the conveyor table and the bottom face of the bandsaw blade. The digital display needs to be calibrated to ensure that the displayed blade height and the actual blade height are the same.

To calibrate the digital display:

1.Resaw a piece of scrap wood. See “Resawing” on Page 27 for more information.

2.Measure the thickness of the workpiece that was cut off between the conveyor table and the blade. Note—Use a precise measuring tool such as calipers or a micrometer.

3.Press the SET key.

4.Enter the thickness value of the cut-off piece measured in Step 2. For example, if the thickness is 1", press 1, 0, 0 on the key pad.

5.Press and hold the SET key for approxi- mately 5 seconds or until the display stops flashing.

The digital display is now calibrated and all blade height values displayed will be the same as the actual distance between the conveyor table and the bottom face of the bandsaw blade.

G0504 16" Horizontal Resaw Bandsaw

-25-

Image 27
Contents Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Parts Service AdjustmentsCommentary General InformationMachine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Circuit Requirements Phase PowerInside of electrical box Grounding Converting toMain motor 440V wiring Main Features Machine FeaturesPage Control Panel Memory Preset Keys A, B, C, D-AllowsUnpacking SET UPAbout this Section Piece InventoryHardware Recognition Chart Clean Up Site Considerations Mounting Resaw to the Floor Removing Resaw from Crate PalletTo install and tension the blade Installing Tensioning BladeAlways de-tension blade after use Adjusting Blade GuidesTo adjust the support bearings To adjust the upper guide block Support BearingConnecting to Dust Power SourceTo connect the resaw to a dust collector Test Run Power on switchOperation Safety Conveyor Controls OperationsTo operate the infeed conveyor To calibrate the digital display Setting Blade HeightCalibrating Digital Display To set the blade height with the keypadTo set the memory function Setting Memory Using Memory ButtonTo store a height in the a memory preset key To use the stored memory preset in the a keyTo perform a resawing operation ResawingBlade Information H1300 H1298 G7984 H2347 H0736 AccessoriesH4959-Coolant Dispenser H0580-Pneumatic Grease GunBelts MaintenanceCleaning MiscellaneousGrease Fittings Check the hydraulic fluid level daily Hydraulic System Minor ServiceTo inspect the hydraulic fluid Hydraulic System Major ServiceTo clean the tank screen To clean the bottom of the tankTo fill the tank with new fluid Service Adjustments About ServiceAdjusting Lower Blade Guides To adjust the tension for the hydraulic pump V-belt Adjusting V-Belt TensionAdjusting Main Conveyor Table Replacing V-BeltsTo check the main conveyor table alignment To set the conveyor tracking Tracking ConveyorsTo replace the conveyor belts Replacing ConveyorsDisconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Underpowered TroubleshootingSymptom Possible Cause Possible Solution Parts Housing PartsDescription Housing Parts ListFrame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Connector 3/8H X 3/8H Hydraulic System Parts ListElectrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page