Grizzly G0504 owner manual Circuit Requirements, Phase Power

Page 11

SECTION 3: CIRCUIT REQUIREMENTS

3-Phase Power

Serious personal injury could occur if you allow power to the machine before complet- ing the setup process. DO NOT allow power to the machine until instructed to do so.

Amperage Draw

The Model G0504 features a 220/440V motor that is prewired for 220V and draws the following amps under maximum load:

Motor Draw at 220V	62.2	Amps
Motor Draw at 440V	31.1	Amps

Circuit Requirements

We recommend connecting your machine to a dedicated and grounded circuit that is rated for the amperage given below. Never replace a circuit breaker on an existing circuit with one of higher amperage without consulting a quali- ﬁed electrician to ensure compliance with wir- ing codes. If you are unsure about the wiring codes in your area or you plan to connect your machine to a shared circuit, consult a qualified electrician.

220V Circuit	80 Amps
440V Circuit	40 Amps

A fire may occur if your particular electrical configuration does not comply with local and state codes. The best way to ensure compli- ance is to check with your local municipality or a qualified electrician.

Connection Type

This machine is intended to be installed in a semi-permanent location and hardwired to the power source by a qualified electrician, using a supply circuit disconnect device with the capa- bility of being locked in the OFF (open) position (see Figure 1).

Figure 1. A power disconnect is preferable to

high current plugs and receptacles.

Figure 2. Power connection points inside the

electrical box.

G0504 16" Horizontal Resaw Bandsaw

-9-

Image 11

Contents Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Parts Service AdjustmentsCommentary General InformationMachine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Circuit Requirements Phase PowerInside of electrical box Grounding Converting toMain motor 440V wiring Main Features Machine FeaturesPage Control Panel Memory Preset Keys A, B, C, D-AllowsUnpacking SET UPAbout this Section Piece InventoryHardware Recognition Chart Clean Up Site Considerations Mounting Resaw to the Floor Removing Resaw from Crate PalletTo install and tension the blade Installing Tensioning BladeAlways de-tension blade after use Adjusting Blade GuidesTo adjust the support bearings To adjust the upper guide block Support BearingTo connect the resaw to a dust collector Connecting to DustPower Source Test Run Power on switchTo operate the infeed conveyor Operation Safety Conveyor ControlsOperations To calibrate the digital display Setting Blade HeightCalibrating Digital Display To set the blade height with the keypadTo set the memory function Setting Memory Using Memory ButtonTo store a height in the a memory preset key To use the stored memory preset in the a keyTo perform a resawing operation ResawingBlade Information H1300 H1298 G7984 H2347 H0736 AccessoriesH4959-Coolant Dispenser H0580-Pneumatic Grease GunBelts MaintenanceCleaning MiscellaneousGrease Fittings Check the hydraulic fluid level daily Hydraulic System Minor ServiceTo inspect the hydraulic fluid Hydraulic System Major ServiceTo fill the tank with new fluid To clean the tank screenTo clean the bottom of the tank Adjusting Lower Blade Guides Service AdjustmentsAbout Service To adjust the tension for the hydraulic pump V-belt Adjusting V-Belt TensionTo check the main conveyor table alignment Adjusting Main Conveyor TableReplacing V-Belts To set the conveyor tracking Tracking ConveyorsTo replace the conveyor belts Replacing ConveyorsDisconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Underpowered TroubleshootingSymptom Possible Cause Possible Solution Parts Housing PartsDescription Housing Parts ListFrame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Connector 3/8H X 3/8H Hydraulic System Parts ListElectrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page