Grizzly G0504 owner manual Electrical System Parts List

Page 70

Electrical System Parts List

REF	PART #	DESCRIPTION

2301	P05042301	DIMENSION SET METER FPC-525/INCH
2302	P05042302	MEMORY BUTTON N/S
2303	P05042303	EMERGENCY BUTTON N/S
2304	P05042304	POWER ON BUTTON N/S
2305	P05042305	UP/LIMIT SWITCH
2306	P05042306	UP BUTTON N/S
2307	P05042307	MOTOR START/GREEN N/S
2308	P05042308	DOWN/LIMIT SWITCH
2309	P05042309	DOWN BUTTON N/S
2310	P05042310	MOTOR STOP/RED N/S
2311	P05042311	NO FUSE SWITCH 3P 100AMP
2312	P05042312	MAG.CONTACTOR LCI-D065 (TE)
2313	P05042313	MAG.CONTACTOR LCI-D096 (TE)
2314	P05042313	MAG.CONTACTOR LCI-D096 (TE)
2315	P05042315	TRANSFORMER 200VA
2316	P05042316	FUSE 5A FUSE
2317	P05042317	ELECTRIC SET 10A/1P
2318	P05042318	POWER SAFETY SWITCH
2319	P05042319	440V CONVERSION KIT (TE)
2320	P05042320	O-L RELAY 220V LR3D-3359 48/65A
2321	P05042321	UP O-L RELAY LR3D-066 1A
2322	P05042322	PHASE REVERSAL RELAY

-68-	G0504 16" Horizontal Resaw Bandsaw

Image 70

Contents Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Service Adjustments PartsGeneral Information CommentaryMachine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Phase Power Circuit RequirementsGrounding Converting to Inside of electrical boxMain motor 440V wiring Machine Features Main FeaturesPage Memory Preset Keys A, B, C, D-Allows Control PanelPiece Inventory SET UPAbout this Section UnpackingHardware Recognition Chart Clean Up Site Considerations Removing Resaw from Crate Pallet Mounting Resaw to the FloorInstalling Tensioning Blade To install and tension the bladeAdjusting Blade Guides Always de-tension blade after useTo adjust the upper guide block Support Bearing To adjust the support bearingsPower Source Connecting to DustTo connect the resaw to a dust collector Power on switch Test RunOperations Operation Safety Conveyor ControlsTo operate the infeed conveyor To set the blade height with the keypad Setting Blade HeightCalibrating Digital Display To calibrate the digital displayTo use the stored memory preset in the a key Setting Memory Using Memory ButtonTo store a height in the a memory preset key To set the memory functionResawing To perform a resawing operationBlade Information H0580-Pneumatic Grease Gun AccessoriesH4959-Coolant Dispenser H1300 H1298 G7984 H2347 H0736Miscellaneous MaintenanceCleaning BeltsGrease Fittings Hydraulic System Minor Service Check the hydraulic fluid level dailyHydraulic System Major Service To inspect the hydraulic fluidTo clean the bottom of the tank To clean the tank screenTo fill the tank with new fluid About Service Service AdjustmentsAdjusting Lower Blade Guides Adjusting V-Belt Tension To adjust the tension for the hydraulic pump V-beltReplacing V-Belts Adjusting Main Conveyor TableTo check the main conveyor table alignment Tracking Conveyors To set the conveyor trackingReplacing Conveyors To replace the conveyor beltsDisconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Troubleshooting UnderpoweredSymptom Possible Cause Possible Solution Housing Parts PartsHousing Parts List DescriptionFrame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Hydraulic System Parts List Connector 3/8H X 3/8HElectrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page