Grizzly G0504 owner manual Rear Hold Down Parts

Page 63

Rear Hold Down Parts

	��	��
		��
	��
		��
	��
		��

��

��

��

�

��

��

��

��

��

		��
		��
�	�	��
	�
		��
��		��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

REF	PART #	DESCRIPTION

2001	PB01M	HEX BOLT M10-1.5 X 30
2002	PLW06M	LOCK WASHER 10MM
2003	PW04M	FLAT WASHER 10MM
2004	P0504753	REAR ROLLER SUPPORT
2005	PN09M	HEX NUT M12-1.75
2006	PLW05M	LOCK WASHER 12MM
2007	PW06M	FLAT WASHER 12MM
2008	P05042008	REAR ROLLER SHAFT
2009	PSB129M	CAP SCREW M12-1.75 X 20
2010	P0504757	REAR PRESSURE PLATE
2011	P0504758	COLLAR
2012	PSS30M	SET SCREW M10-1.5 X 10

REF	PART #	DESCRIPTION

2013	P05042013	FIXED SEAT
2014	PSB14M	CAP SCREW M8-1.25 X 20
2015	PLW04M	LOCK WASHER 8MM
2016	PW01M	FLAT WASHER 8MM
2017	PSB77M	CAP SCREW M12-1.75 X 30
2018	P05042018	REAR ROLLER SHAFT
2019	P0504747	PRESSURE ROLLER WHEEL
2020	P0504763	COLLAR
2021	P05042021	SHOCK ABSORBER
2022	PB125M	HEX BOLT M12-1.75 X 65
2023	PB141M	HEX BOLT M12-1.75 X 80

G0504 16" Horizontal Resaw Bandsaw

-61-

Image 63

Contents Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Parts Service AdjustmentsCommentary General InformationMachine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Circuit Requirements Phase PowerInside of electrical box Grounding Converting toMain motor 440V wiring Main Features Machine FeaturesPage Control Panel Memory Preset Keys A, B, C, D-AllowsUnpacking SET UPAbout this Section Piece InventoryHardware Recognition Chart Clean Up Site Considerations Mounting Resaw to the Floor Removing Resaw from Crate PalletTo install and tension the blade Installing Tensioning BladeAlways de-tension blade after use Adjusting Blade GuidesTo adjust the support bearings To adjust the upper guide block Support BearingConnecting to Dust Power SourceTo connect the resaw to a dust collector Test Run Power on switchOperation Safety Conveyor Controls OperationsTo operate the infeed conveyor To calibrate the digital display Setting Blade HeightCalibrating Digital Display To set the blade height with the keypadTo set the memory function Setting Memory Using Memory ButtonTo store a height in the a memory preset key To use the stored memory preset in the a keyTo perform a resawing operation ResawingBlade Information H1300 H1298 G7984 H2347 H0736 AccessoriesH4959-Coolant Dispenser H0580-Pneumatic Grease GunBelts MaintenanceCleaning MiscellaneousGrease Fittings Check the hydraulic fluid level daily Hydraulic System Minor ServiceTo inspect the hydraulic fluid Hydraulic System Major ServiceTo clean the tank screen To clean the bottom of the tankTo fill the tank with new fluid Service Adjustments About ServiceAdjusting Lower Blade Guides To adjust the tension for the hydraulic pump V-belt Adjusting V-Belt TensionAdjusting Main Conveyor Table Replacing V-BeltsTo check the main conveyor table alignment To set the conveyor tracking Tracking ConveyorsTo replace the conveyor belts Replacing ConveyorsDisconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Underpowered TroubleshootingSymptom Possible Cause Possible Solution Parts Housing PartsDescription Housing Parts ListFrame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Connector 3/8H X 3/8H Hydraulic System Parts ListElectrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page