Grizzly G0504 owner manual Test Run, Power on switch

Page 25

Test Run

Before starting the resaw, make sure you have performed the preceding assembly and adjustment instructions, and you have read through the rest of the manual and are familiar with the various functions and safety issues associated with this machine. Failure to follow this warning could result in serious personal injury or even death!

To test run the resaw:

1.Make sure the wheel cover and electrical box is closed and all tools or other objects are cleared away from the machine.

2.Put on safety glasses and make sure any bystanders are out of the way and also wear- ing safety glasses.

3.Tension the blade.

4.Turn ON the master switch that is located on the outside of the electrical box.

5.Turn the POWER ON switch (shown in Figure 21) clockwise.

Figure 21. POWER ON switch.

6.Press the UP and DOWN buttons to make sure the resaw head moves in the proper direction.

—If the resaw head moves in the opposite direction as indicated, then the machine has been wired out of phase. To cor- rect this, disconnect the power to the machine, open the electrical box, and switch any two current carrying wires (R, S, or T) that connect the machine to the power source.

7.Push the emergency stop button in, then twist it clockwise until it pops out.

8.Once you have performed Steps 1-4and everything is okay with the machine and set up, press the MOTOR START button. As you are standing in front of the machine, make sure that the blade is moving from left to right.

9.Press the conveyor lever forward to test the conveyor belt.

—If any problems occur, press the EMG STOP button. Investigate and cor- rect the problem before operating the machine further. If you need help, refer to the troubleshooting section in the back of this manual.

—If you cannot easily locate the source of an unusual noise or vibration by yourself, please contact our service department at (570) 546-9663.

G0504 16" Horizontal Resaw Bandsaw

-23-

Image 25

Contents Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Parts Service AdjustmentsCommentary General InformationMachine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Circuit Requirements Phase PowerInside of electrical box Grounding Converting toMain motor 440V wiring Main Features Machine FeaturesPage Control Panel Memory Preset Keys A, B, C, D-AllowsAbout this Section SET UPPiece Inventory UnpackingHardware Recognition Chart Clean Up Site Considerations Mounting Resaw to the Floor Removing Resaw from Crate PalletTo install and tension the blade Installing Tensioning BladeAlways de-tension blade after use Adjusting Blade GuidesTo adjust the support bearings To adjust the upper guide block Support BearingPower Source Connecting to DustTo connect the resaw to a dust collector Test Run Power on switchOperations Operation Safety Conveyor ControlsTo operate the infeed conveyor Calibrating Digital Display Setting Blade HeightTo set the blade height with the keypad To calibrate the digital displayTo store a height in the a memory preset key Setting Memory Using Memory ButtonTo use the stored memory preset in the a key To set the memory functionTo perform a resawing operation ResawingBlade Information H4959-Coolant Dispenser AccessoriesH0580-Pneumatic Grease Gun H1300 H1298 G7984 H2347 H0736Cleaning MaintenanceMiscellaneous BeltsGrease Fittings Check the hydraulic fluid level daily Hydraulic System Minor ServiceTo inspect the hydraulic fluid Hydraulic System Major ServiceTo clean the bottom of the tank To clean the tank screenTo fill the tank with new fluid About Service Service AdjustmentsAdjusting Lower Blade Guides To adjust the tension for the hydraulic pump V-belt Adjusting V-Belt TensionReplacing V-Belts Adjusting Main Conveyor TableTo check the main conveyor table alignment To set the conveyor tracking Tracking ConveyorsTo replace the conveyor belts Replacing ConveyorsDisconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Underpowered TroubleshootingSymptom Possible Cause Possible Solution Parts Housing PartsDescription Housing Parts ListFrame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Connector 3/8H X 3/8H Hydraulic System Parts ListElectrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page