Grizzly G0504 owner manual Service Adjustments, About Service, Adjusting Lower Blade Guides

Page 37

SECTION 8: SERVICE ADJUSTMENTS

Always disconnect power to the machine before performing ser- vice adjustments. Failure to do this may result in serious personal injury.

About Service

This section is designed to help the operator with adjustments that were made at the factory and that might also need to be made during the life of the machine.

This section is provided for your convenience— it is not a substitute for the Grizzly Service Department. If any adjustments arise that are not described in this manual, then feel free to call the Grizzly Technical Support at (570) 546-9663.

Adjusting Lower

Blade Guides

The instructions on adjusting the upper guide blocks and support bearing are given in Section

5:Set Up. This section focuses on adjusting the lower blade guides, which is a non-routine adjustment that would typically be done before the upper blade guide and support bearing would be adjusted.

To adjust the lower blade guides:

1.Disconnect the resaw from the power source!

2.Open the wheel cover for easy access to the blade guide assemblies.

3.Make sure the blade is tensioned in the same manner that will be used for operation.

4.Loosen the lateral adjustment bolts (shown in Figure 34).

	Lateral
Vertical	Adjustment Bolts
Adjustment Bolts

Figure 34. Lower guide block adjustment bolts.

5.Adjust the assembly so the blade guides are approximately 1⁄16" behind the gullets of the blade teeth, and tighten the lateral bolts.

6.Loosen the vertical adjustment bolts.

7.Adjust the lower blade guide so it barely touches the bottom of the blade, then tighten the vertical adjustment bolts.

8.Repeat Steps 4-5on the other blade guide.

9.Adjust the upper guide blocks and the sup- port bearings.

10.Close the wheel cover.

G0504 16" Horizontal Resaw Bandsaw

-35-

Image 37

Contents Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Parts Service AdjustmentsCommentary General InformationMachine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Circuit Requirements Phase PowerInside of electrical box Grounding Converting toMain motor 440V wiring Main Features Machine FeaturesPage Control Panel Memory Preset Keys A, B, C, D-AllowsAbout this Section SET UPPiece Inventory UnpackingHardware Recognition Chart Clean Up Site Considerations Mounting Resaw to the Floor Removing Resaw from Crate PalletTo install and tension the blade Installing Tensioning BladeAlways de-tension blade after use Adjusting Blade GuidesTo adjust the support bearings To adjust the upper guide block Support BearingPower Source Connecting to DustTo connect the resaw to a dust collector Test Run Power on switchOperations Operation Safety Conveyor ControlsTo operate the infeed conveyor Calibrating Digital Display Setting Blade HeightTo set the blade height with the keypad To calibrate the digital displayTo store a height in the a memory preset key Setting Memory Using Memory ButtonTo use the stored memory preset in the a key To set the memory functionTo perform a resawing operation ResawingBlade Information H4959-Coolant Dispenser AccessoriesH0580-Pneumatic Grease Gun H1300 H1298 G7984 H2347 H0736Cleaning MaintenanceMiscellaneous BeltsGrease Fittings Check the hydraulic fluid level daily Hydraulic System Minor ServiceTo inspect the hydraulic fluid Hydraulic System Major ServiceTo clean the bottom of the tank To clean the tank screenTo fill the tank with new fluid About Service Service AdjustmentsAdjusting Lower Blade Guides To adjust the tension for the hydraulic pump V-belt Adjusting V-Belt TensionReplacing V-Belts Adjusting Main Conveyor TableTo check the main conveyor table alignment To set the conveyor tracking Tracking ConveyorsTo replace the conveyor belts Replacing ConveyorsDisconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Underpowered TroubleshootingSymptom Possible Cause Possible Solution Parts Housing PartsDescription Housing Parts ListFrame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Connector 3/8H X 3/8H Hydraulic System Parts ListElectrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page