Baldor MN735 Reset to Factory Settings 2 button Reset, Select Local or Remote, Remote to Local

Page 33

Power Up On initial power–up, the drive is in Local control mode and the keypad will display the Local Setpoint.

.

All parameters are at factory settings. Any changes to these conditions are automatically saved. The drive will initialize on subsequent power–ups with the previously saved settings and control mode.

How to Change a Parameter Value

You can change the values of parameters stored in the and menus. Refer to “Parameter Definitions” for further information.

•View the parameter to be edited and press to display the parameter’s value.

•Select the digit to be changed (pressing the key moves the cursor from right to left).

•Use the keys to adjust the value. Hold the key momentarily to adjust the value marginally, or hold the key to make rapid changes; the rate of change varies with the time held.

•Press to return to the parameter display. The new value is stored.

Special Menu Features

Reset to Factory Settings (2 button Reset)

Turn power on while pressing the Y and B keys. This loads or restores the factory settings and application 1.

HOLD

Then press

Select Local or Remote

Remote Control Mode: Allows control using digital and analog inputs and outputs. Local control keys are inactive when Remote control mode is selected. In remote mode, the control uses a remote setpoint (analog Input 1).

Local Control Mode: Provides local control and monitoring of the drive using the keypad. In local mode, the control uses the local setpoint parameter (value is adjusted using the keypad).

Note: You can only change between Local and Remote control when the Inverter

is “stopped”, and either	or the Local Setpoint is displayed.
Remote to Local

Note: For safety reasons, the control will not return to Remote mode if this will cause the drive to start. Verify that the RUN and JOG inputs are low.

4–4 Start–Up and Operation

MN735

Image 33

Contents MN735 Series 35D Inverter ControlTable of Contents Appendix B Appendix aSection Quick Start Power and Motor ConnectionsSize 1 and 3 Terminal Strips Remote ModeThermistor Connection to motor thermistor Power Connection DescriptionsTerminal Signal Name Description Range Analog/Digital Signal DescriptionsSection General Information Limited WarrantyProduct Notice Intended use Could result in damage to propertyOn next Precautions To prevent equipment damage, be certain that the input power Section Receiving & Installation Receiving & InspectionLocation and Mounting Inverter Sizes Watts Loss Ratings Catalog No Output CurrentPower Conditioning Input Power ConditioningUngrounded Distribution System Impedance + Clamp Terminal Unshielded and Shielded CouplingsAWG MM2 Wire SizePower Connection Descriptions Power and Ground Connections Size 2 Shown Resistance thresholds are Rising temperature trip resistance One control to PE Receiving & Installation MN735 External Brake Resistor Keypad Connection Diagram Keypad ModeStandard Run Connection Diagram Standard Run 3 Wire ModeRelated Parameters Speed 2 Wire Mode10 Epot Connection Diagram 11 Epot Connection Diagram 12 PID Connection Diagram PID 2 Wire ModeReceiving & Installation MN735 Keypad Description Section Start-Up and OperationDiagnostics Menu DisplayDrive Status Indications shown on keypad Menu Level Reset to Factory Settings 2 button Reset Select Local or RemoteRemote to Local Quick Application Selection Password ProtectionParameter Definitions Display Parameter Description Range Factory SettingDisplay Parameter Description Range PI P Gain Analog Output Relay Invert =FALSE =TRUE Method for Setting-up the PI Gains Proportional Gain P501Integral P502 Current Power Dependent Parameters Inverter Size Factory SettingSaving Your Application Data Routine MaintenanceMaterial Recycle Disposal PackagingSection Troubleshooting Reset a TripTrips DC Link Ripple General FailuresGeneral Specifications Section Specifications & Product DataControl Specifications Keypad DisplayAnalog Inputs Digital Inputs Analog OutputsRelay Output Ratings CatalogDimensions Size 3 230VAC 3 Phase Size 1 and 2 230VAC 1 Phase460VAC 3 Phase Controls Size 2 and 3 460VAC Appendix a Dynamic BrakeTable A-1 External Brake Resistor Selection Appendix B CE Guidelines Wiring of Shielded Screened CablesCE Declaration of Conformity EMC Conformity and CE MarkingCabinet EMC Wiring TechniqueCable Screens Grounding EMC Installation InstructionsInput Signal Cable Grounding Date 1/5/02 EC Declarations of Conformity Standard EMC DirectiveTion CE Guidelines MN735  Baldor Electric Company MN735 02 C&J Box Ft. Smith, AR 479 Fax 479