Baldor MN735 manual Date 1/5/02 EC Declarations of Conformity, Standard EMC Directive, Tion

Page 56

Baldor UK Limited

Mint Motion Centre

Hawkley Drive.

Bristol Distribution Centre,

Bristol, BS32 0BF

United Kingdom

Tel: (+44) 01454 850000

Date: 1/5/02 EC Declarations of Conformity	Ref: DE00013–000

This is to certify that Baldors Inverter products comply with the requirements of CE Directive as described below and being one of:–

35D Family

37D Family

38D Family

When used in accordance with the guidance and instructions given in the corresponding Product Installation Manual, the above Electronic Products conform with the protection requirements of Council Directive 89/336/EEC and amended by 92/31/EEC and 93/68/EEC, Article 10 and Annex 1, relating to the EMC Directive and Manufacturers Declaration for EMC, by the application of the relevant clauses of the following standards:

	Standard	EMC Directive	Manufacturers Declara-
	Standard	EMC Directive	tion
			tion
	BSEN 500081–1: 1992 &/or	n	n
	BSEN50081–2
	(1994): 1996	n	n
	BSEN 50082–1#: 1998	n	n
	BSEN 50082–2#: 1995	n	n
	BSEN 61800–3 : 1996	n	n
	BSEN 61000–3–2: 1995	n	n

#compliant with these immunity standards without specifed EMC Filters and with the protection requirements of Council Directive 72/23/EEC (amended by 93/68/EEC) article 13 and Annex III relating to Low Voltage Equipment, by following the guidance found in the relevant clauses of the following standard:–

Standard	Title
EN50178: 1997	Electronic equipment for use in power installations

Machinery Directive

The above Electronic Products are components to be incorporated into machinery and may not be operated alone. The complete machinery or installation using this equipment may only be put in to service when the safety considerations of the Directive 89/392/EEC are fully adhered to. Particular reference should be made to EN60204–1 (Safety of Machinery – Electrical Equipment of Machines). All instructions, warnings and safety information of the Product Installation Manual must be adhered to.

Signed: .....................................

Dr. Gerry Boast

Engineering Manager

MN735

CE Guidelines B–5

Image 56

Contents Series 35D Inverter Control MN735Table of Contents Appendix a Appendix BPower and Motor Connections Section Quick StartRemote Mode Size 1 and 3 Terminal StripsPower Connection Descriptions Thermistor Connection to motor thermistorAnalog/Digital Signal Descriptions Terminal Signal Name Description RangeLimited Warranty Section General InformationOn next Product Notice Intended useCould result in damage to property Precautions To prevent equipment damage, be certain that the input power Location and Mounting Section Receiving & InstallationReceiving & Inspection Watts Loss Ratings Catalog No Output Current Inverter SizesUngrounded Distribution System Power ConditioningInput Power Conditioning Impedance + Unshielded and Shielded Couplings Clamp TerminalWire Size AWG MM2Power Connection Descriptions Power and Ground Connections Size 2 Shown Resistance thresholds are Rising temperature trip resistance One control to PE Receiving & Installation MN735 External Brake Resistor Keypad Mode Keypad Connection DiagramStandard Run 3 Wire Mode Standard Run Connection DiagramSpeed 2 Wire Mode Related Parameters10 Epot Connection Diagram 11 Epot Connection Diagram PID 2 Wire Mode 12 PID Connection DiagramReceiving & Installation MN735 Section Start-Up and Operation Keypad DescriptionDrive Status Indications shown on keypad Diagnostics MenuDisplay Menu Level Remote to Local Reset to Factory Settings 2 button ResetSelect Local or Remote Password Protection Quick Application SelectionDisplay Parameter Description Range Factory Setting Parameter DefinitionsDisplay Parameter Description Range PI P Gain Analog Output Relay Invert =FALSE =TRUE Integral P502 Method for Setting-up the PI GainsProportional Gain P501 Power Dependent Parameters Inverter Size Factory Setting CurrentRoutine Maintenance Saving Your Application DataMaterial Recycle Disposal PackagingTrips Section TroubleshootingReset a Trip General Failures DC Link RippleSection Specifications & Product Data General SpecificationsAnalog Inputs Control SpecificationsKeypad Display Analog Outputs Digital InputsRelay Output Ratings CatalogDimensions Size 1 and 2 230VAC 1 Phase Size 3 230VAC 3 Phase460VAC 3 Phase Controls Size 2 and 3 460VAC Appendix a Dynamic BrakeTable A-1 External Brake Resistor Selection Wiring of Shielded Screened Cables Appendix B CE GuidelinesCE Declaration of Conformity EMC Conformity and CE MarkingEMC Wiring Technique CabinetEMC Installation Instructions Cable Screens GroundingInput Signal Cable Grounding Tion Date 1/5/02 EC Declarations of ConformityStandard EMC Directive CE Guidelines MN735 Box Ft. Smith, AR 479 Fax 479  Baldor Electric Company MN735 02 C&J