Baldor MN735 manual Speed 2 Wire Mode, Related Parameters

Page 25

3 – 3 Speed 2 Wire Mode

In 3 speed 2 wire mode, the control is operated by the opto isolated inputs and the analog command input. The opto inputs can be switches as shown in Figure 3-9 or logic signals from another device.

Figure 3-9 3 Speed Connection Diagram

Speed

Select

 

1

2

Command

Open

Open

Analog Input 1 & 2 (Add)

Open

Closed

Preset Speed 1

Closed

Open

Preset Speed 2

Closed

Closed

Preset Speed 3

 

 

 

Related Parameters

Speed Select 2

Speed Select 1

Run REV

Run FWD

+24VDC

Speed Output

Pot Reference

10

9

8

7

6

5

4

p302 Preset Speed 1

p303 Preset Speed 2

p304 Preset Speed 3

10KW Pot or

0-10VDC

Analog Input 2

Analog Input 1

Analog GND

3

2

1

Analog Input 1 = 0–10VDC Setpoint

Analog Input 2 = 4–20mA Setpoint

Fault

RLY1A

RLY1B

1Analog GND. Reference for analog inputs.

2Setpoint 0–10VDC. Single ended analog voltage input, referenced to 1.

3Setpoint 4–20mA. Single ended analog current input, referenced to 1.

4+10VDC reference voltage for potentiometer.

5Analog output that represents the commanded speed output.

6+24VDC for Optical Inputs power.

7CLOSED starts motor operation in the Forward direction.

8CLOSED starts motor operation in the Reverse direction.

9Speed Select input 1. Inputs 9 & 10 select preset speeds 1 to 3.

10Speed Select input 2. Inputs 9 & 10 select preset speeds 1 to 3. RLY1 Digital output that represents the fault status.

3–14 Receiving & Installation

MN735

Image 25
Contents MN735 Series 35D Inverter ControlTable of Contents Appendix B Appendix aSection Quick Start Power and Motor ConnectionsSize 1 and 3 Terminal Strips Remote ModeThermistor Connection to motor thermistor Power Connection DescriptionsTerminal Signal Name Description Range Analog/Digital Signal DescriptionsSection General Information Limited WarrantyCould result in damage to property Product Notice Intended useOn next Precautions To prevent equipment damage, be certain that the input power Receiving & Inspection Section Receiving & InstallationLocation and Mounting Inverter Sizes Watts Loss Ratings Catalog No Output CurrentInput Power Conditioning Power ConditioningUngrounded Distribution System Impedance + Clamp Terminal Unshielded and Shielded CouplingsAWG MM2 Wire SizePower Connection Descriptions Power and Ground Connections Size 2 Shown Resistance thresholds are Rising temperature trip resistance One control to PE Receiving & Installation MN735 External Brake Resistor Keypad Connection Diagram Keypad ModeStandard Run Connection Diagram Standard Run 3 Wire ModeRelated Parameters Speed 2 Wire Mode10 Epot Connection Diagram 11 Epot Connection Diagram 12 PID Connection Diagram PID 2 Wire ModeReceiving & Installation MN735 Keypad Description Section Start-Up and OperationDisplay Diagnostics MenuDrive Status Indications shown on keypad Menu Level Select Local or Remote Reset to Factory Settings 2 button ResetRemote to Local Quick Application Selection Password ProtectionParameter Definitions Display Parameter Description Range Factory SettingDisplay Parameter Description Range PI P Gain Analog Output Relay Invert =FALSE =TRUE Proportional Gain P501 Method for Setting-up the PI GainsIntegral P502 Current Power Dependent Parameters Inverter Size Factory SettingSaving Your Application Data Routine MaintenanceMaterial Recycle Disposal PackagingReset a Trip Section TroubleshootingTrips DC Link Ripple General FailuresGeneral Specifications Section Specifications & Product DataKeypad Display Control SpecificationsAnalog Inputs Digital Inputs Analog OutputsRelay Output Ratings CatalogDimensions Size 3 230VAC 3 Phase Size 1 and 2 230VAC 1 Phase460VAC 3 Phase Controls Size 2 and 3 460VAC Appendix a Dynamic BrakeTable A-1 External Brake Resistor Selection Appendix B CE Guidelines Wiring of Shielded Screened CablesCE Declaration of Conformity EMC Conformity and CE MarkingCabinet EMC Wiring TechniqueCable Screens Grounding EMC Installation InstructionsInput Signal Cable Grounding Standard EMC Directive Date 1/5/02 EC Declarations of ConformityTion CE Guidelines MN735  Baldor Electric Company MN735 02 C&J Box Ft. Smith, AR 479 Fax 479