Kohler 8/10/12RESVL manual Generator Metering Menu, Voltage Calibration

Page 38

3.11 Generator Metering Menu

The generator metering menu displays the generator voltage and frequency. See Figure 3-12.

Voltage Calibration

DANGER

Hazardous voltage.

Will cause severe injury or death.

This equipment must be installed and serviced by qualified electrical personnel.

The voltage calibration mode can be entered from the Generator Metering menu. Contact a Kohler-authorized distributor/dealer for service.

The Reset Calibration menu allows you to set the voltage reading back to the original value after calibration, if necessary. See Figure 3-12.

Generator ---->
Metering
Three-phase	Single-phase
Three-phase
Volts L1--L2:	Volts:	Note: Actual settings may vary.
240 V		240 V
Volts L2--L3:	Frequency:
240 V		60.0 Hz
Volts L3--L1:
240 V
Frequency:
60.0 Hz
	Reset	Reset
	Calibration	Calib? No
	<---- Return	Reset
	<---- Return	Calib? Yes
		Calib? Yes

tp6810

Figure 3-12Generator Metering Menu

38 Section 3 RDC2 Controller Operation

TP-6880 10/14

Image 38

Contents RDC2 TP-6880 10/14aGenerator Set Identification Numbers Accessory Number Accessory DescriptionProduct Identification Information Controller IdentificationTable of Contents DC2 Controller Operation Scheduled MaintenanceTroubleshooting Accidental Starting Safety Precautions and InstructionsBattery Accidental starting Can cause severe injury or deathCarbon monoxide Can Cause Engine Backfire/Flash FireExhaust System Fire Can cause severe injury or deathFuel System Hazardous Noise Hazardous voltage Will cause severe injury or deathHeavy Equipment Hot PartsIntroduction Transfer Switch LiteratureAccessory Literature List of Related LiteratureGenerator Set Application NameplateEmission Information Emission Compliance PeriodService Assistance Service Assistance TP-6880 10/14 Descriptions and Service Views RDC2 Controller Features DC2 Controller Features Programmable Interface Module PIM AccessoriesCarburetor Heater Load Control Module LCMService Views 12143Service View Prestart Checklist Generator Set OperationGenerator Set Operation TP-6880 10/14 Exercising the Generator Set Generator Set OperationUnloaded Cycle Exercise with Complete System Diagnostics Automatic Operation with Other Transfer SwitchesSetting the Exerciser ExerciseUnloaded Full-Speed Exercise Power Failure During Exercise CycleSystem Diagnostics Loaded Full-Speed Exercise with RXT onlyResetting the Controller after a Fault Shutdown FaultsATS Communication Errors ShutdownsFault Message Shutdown SD Condition Check 3Controller Fault Messages Fault Shutdown SD Condition CheckGenerator Enclosure Thermostat Generator Set Operation TP-6880 10/14 RDC2 Controller Operation RDC2 Generator Set/ Transfer Switch ControllerControls and Indicators Button Function Controller Keypad LED IndicatorsButton LED OperationLCD Display Active AlertChanging Settings Controller PowerBattery Charging Procedure to Change SettingsChanging Settings on the RDC2 Controller 7Changing SettingsChanging the Exercise Settings Setting the ExerciserSetting the Exerciser at Controller Power-up Procedure to Set the Exerciser8Procedure to Set the Exerciser on the RDC2 Controller RDC2 Controller Menus Main MenuOverview Menu Engine Metering MenuGenerator Metering Menu Voltage CalibrationGenerator Set Information Menu Genset Run Time MenuGenset System Menu Setting the ExerciserAdjusting the Display Contrast Voltage Regulator VR Voltage AdjATS Status Menu Screens on this page do not appearATS Configuration Menu Changing ATS Configuration SettingsDate and Time Menu Networking Information MenusNetworking Status Submenu DhcpDhcp Submenu Networking Configuration Submenu OnCue Plus PasswordPassword 21Network Configuration Submenu Rbus Information 22RBUS Information SubmenuRemote Devices Submenu From FigureProgrammable Interface Module PIM Status Menu Load Control Module LCM or Load Shed Kit Menus 25Load Control Module LCM or Load Shed Kit Status MenuProcedure to View Event History Event LogRDC2 Controller Operation TP-6880 10/14 DC2 Generator Set/ Transfer Switch Controller DC2 Controller OperationLED Indication Controller KeypadButton Button Function Description5Status Displays, Generator Running Exerciser Reset Exercise ModesMaintenance Timer OnCue Plus PasswordDC2 Controller Operation TP-6880 10/14 Scheduled Maintenance Scheduled Maintenance Service Schedule Engine Oil Recommendation Oil Change ProcedureLubrication System Low Oil Pressure ShutdownReplace the oil filter Reset the maintenance timer on the controllerDrain the oil Fill with oilModel Resv RDC2 Resetting the Maintenance TimerSpark Plugs Model Resvl DC2Paper Element Service Air Cleaner ServiceAir Cleaner, 8RESV/RESVL Models Air Cleaner, 10/12RESV/RESVL Models Cooling SystemHazardous noise Can cause hearing loss EZ-273000-J Storage Procedure Scheduled Maintenance TP-6880 10/14 Introduction TroubleshootingFault Messages USB PortTroubleshooting Problem Possible Cause Corrective ActionAppendix a Abbreviations AnsiLCB Page TP-6880 10/14