Kohler 8/10/12RESVL manual ATS Configuration Menu, Changing ATS Configuration Settings

Page 42

3.16 ATS Configuration Menu

Note: The ATS Configuration menu appears only if a Model RXT transfer switch is connected.

Use the ATS Configuration submenu to check the Model RXT transfer switch system settings and time delays, and change the settings, if necessary.

Changing ATS Configuration Settings

To enable editing, press the select button. The value flashes to indicate that it can be changed. Press the up and down arrow buttons to change the value. Press the Select button to save the value shown.

Use the up and down arrow buttons to move to the next value to be changed. Repeat the adjustment process until all values are correct.

Press the down arrow until Return is displayed. Press the select button to return to the main menu.

ATS ---->

Configuration

Normal Freq: 12.3 Hz

Normal Voltage: 12345.6 V

Emerg. Freq: 12.3 Hz

Emerg. Voltage: 12345.6 V

Emerg. Engine Start: 3 sec

Transfer From

3 sec Normal:

Transfer From Emerg.: 120 sec

<---- Return

Note: Actual settings may vary.

tp6810

Figure 3-17ATS Configuration Menu

42 Section 3 RDC2 Controller Operation

TP-6880 10/14

Image 42
Contents RDC2 TP-6880 10/14aGenerator Set Identification Numbers Accessory Number Accessory DescriptionProduct Identification Information Controller IdentificationTable of Contents Scheduled Maintenance TroubleshootingDC2 Controller Operation Accidental Starting Safety Precautions and InstructionsBattery Accidental starting Can cause severe injury or deathCarbon monoxide Can Cause Engine Backfire/Flash FireExhaust System Fire Can cause severe injury or deathFuel System Hazardous Noise Hazardous voltage Will cause severe injury or deathHeavy Equipment Hot PartsIntroduction Transfer Switch LiteratureAccessory Literature List of Related LiteratureGenerator Set Application NameplateEmission Information Emission Compliance PeriodService Assistance Service Assistance TP-6880 10/14 Descriptions and Service Views RDC2 Controller Features DC2 Controller Features Programmable Interface Module PIM AccessoriesCarburetor Heater Load Control Module LCMService Views 12143Service View Prestart Checklist Generator Set OperationGenerator Set Operation TP-6880 10/14 Exercising the Generator Set Generator Set OperationUnloaded Cycle Exercise with Complete System Diagnostics Automatic Operation with Other Transfer SwitchesSetting the Exerciser ExerciseUnloaded Full-Speed Exercise Power Failure During Exercise CycleSystem Diagnostics Loaded Full-Speed Exercise with RXT onlyResetting the Controller after a Fault Shutdown FaultsATS Communication Errors ShutdownsFault Message Shutdown SD Condition Check 3Controller Fault Messages Fault Shutdown SD Condition CheckGenerator Enclosure Thermostat Generator Set Operation TP-6880 10/14 RDC2 Generator Set/ Transfer Switch Controller Controls and IndicatorsRDC2 Controller Operation Button Function Controller Keypad LED IndicatorsButton LED OperationLCD Display Active AlertChanging Settings Controller PowerBattery Charging Procedure to Change SettingsChanging Settings on the RDC2 Controller 7Changing SettingsChanging the Exercise Settings Setting the ExerciserSetting the Exerciser at Controller Power-up Procedure to Set the Exerciser8Procedure to Set the Exerciser on the RDC2 Controller RDC2 Controller Menus Main MenuOverview Menu Engine Metering MenuGenerator Metering Menu Voltage CalibrationGenerator Set Information Menu Genset Run Time MenuGenset System Menu Setting the ExerciserAdjusting the Display Contrast Voltage Regulator VR Voltage AdjATS Status Menu Screens on this page do not appearATS Configuration Menu Changing ATS Configuration SettingsDate and Time Menu Networking Information MenusNetworking Status Submenu DhcpNetworking Configuration Submenu OnCue Plus Password PasswordDhcp Submenu 21Network Configuration Submenu Rbus Information 22RBUS Information SubmenuRemote Devices Submenu From FigureProgrammable Interface Module PIM Status Menu Load Control Module LCM or Load Shed Kit Menus 25Load Control Module LCM or Load Shed Kit Status MenuProcedure to View Event History Event LogRDC2 Controller Operation TP-6880 10/14 DC2 Generator Set/ Transfer Switch Controller DC2 Controller OperationLED Indication Controller KeypadButton Button Function Description5Status Displays, Generator Running Exerciser Reset Exercise ModesMaintenance Timer OnCue Plus PasswordDC2 Controller Operation TP-6880 10/14 Scheduled Maintenance Scheduled Maintenance Service Schedule Engine Oil Recommendation Oil Change ProcedureLubrication System Low Oil Pressure ShutdownReplace the oil filter Reset the maintenance timer on the controllerDrain the oil Fill with oilModel Resv RDC2 Resetting the Maintenance TimerSpark Plugs Model Resvl DC2Air Cleaner Service Air Cleaner, 8RESV/RESVL ModelsPaper Element Service Air Cleaner, 10/12RESV/RESVL Models Cooling SystemHazardous noise Can cause hearing loss EZ-273000-J Storage Procedure Scheduled Maintenance TP-6880 10/14 Introduction TroubleshootingFault Messages USB PortTroubleshooting Problem Possible Cause Corrective ActionAppendix a Abbreviations AnsiLCB Page TP-6880 10/14