Kohler 8/10/12RESVL manual Networking Status Submenu, Dhcp

Page 44

3.18.1 Networking Status Submenu

The Networking Status submenu contains settings for OnCuer Plus. See the OnCue Plus Software Operation Manual for information about the appropriate network settings for OnCue Plus. Changes to these settings are not typically required.

If DHCP is enabled, IP parameters are not displayed. If DHCP is disabled (i.e., if a static IP address is used), the IP parameters are displayed.

To enable or disable DHCP and change the IP settings, go to the Networking Configuration menu. See Section 3.18.2.

Networking---->

Information

Networking---->

Status

OnCue Status: Connected

DHCP:

Enabled

IP Address: 123.456.789.123

Subnet Mask: 123.456.789.123

Gateway:

123.456.789.123

DNS 1: 123.456.789.123

DNS 2: 123.456.789.123

Ethernet Status:

Disconnected

OnCue Server: 123.456.789.123

<---- Return

tp6804

Figure 3-20Network Status Submenu

44 Section 3 RDC2 Controller Operation

TP-6880 10/14

Image 44

Contents RDC2 TP-6880 10/14aAccessory Number Accessory Description Product Identification InformationGenerator Set Identification Numbers Controller IdentificationTable of Contents DC2 Controller Operation Scheduled MaintenanceTroubleshooting Safety Precautions and Instructions BatteryAccidental Starting Accidental starting Can cause severe injury or deathEngine Backfire/Flash Fire Exhaust SystemCarbon monoxide Can Cause Fire Can cause severe injury or deathFuel System Hazardous Noise Hazardous voltage Will cause severe injury or deathHeavy Equipment Hot PartsTransfer Switch Literature Accessory LiteratureIntroduction List of Related LiteratureNameplate Emission InformationGenerator Set Application Emission Compliance PeriodService Assistance Service Assistance TP-6880 10/14 Descriptions and Service Views RDC2 Controller Features DC2 Controller Features Accessories Carburetor HeaterProgrammable Interface Module PIM Load Control Module LCMService Views 12143Service View Prestart Checklist Generator Set OperationGenerator Set Operation TP-6880 10/14 Exercising the Generator Set Generator Set OperationAutomatic Operation with Other Transfer Switches Setting the ExerciserUnloaded Cycle Exercise with Complete System Diagnostics ExercisePower Failure During Exercise Cycle System DiagnosticsUnloaded Full-Speed Exercise Loaded Full-Speed Exercise with RXT onlyFaults ATS Communication ErrorsResetting the Controller after a Fault Shutdown ShutdownsFault Message Shutdown SD Condition Check 3Controller Fault Messages Fault Shutdown SD Condition CheckGenerator Enclosure Thermostat Generator Set Operation TP-6880 10/14 RDC2 Controller Operation RDC2 Generator Set/ Transfer Switch ControllerControls and Indicators Controller Keypad LED Indicators ButtonButton Function LED OperationLCD Display Active AlertController Power Battery ChargingChanging Settings Procedure to Change SettingsChanging Settings on the RDC2 Controller 7Changing SettingsSetting the Exerciser Setting the Exerciser at Controller Power-upChanging the Exercise Settings Procedure to Set the Exerciser8Procedure to Set the Exerciser on the RDC2 Controller RDC2 Controller Menus Main MenuOverview Menu Engine Metering MenuGenerator Metering Menu Voltage CalibrationGenerator Set Information Menu Genset Run Time MenuSetting the Exerciser Adjusting the Display ContrastGenset System Menu Voltage Regulator VR Voltage AdjATS Status Menu Screens on this page do not appearATS Configuration Menu Changing ATS Configuration SettingsDate and Time Menu Networking Information MenusNetworking Status Submenu DhcpDhcp Submenu Networking Configuration Submenu OnCue Plus PasswordPassword 21Network Configuration Submenu Rbus Information 22RBUS Information SubmenuRemote Devices Submenu From FigureProgrammable Interface Module PIM Status Menu Load Control Module LCM or Load Shed Kit Menus 25Load Control Module LCM or Load Shed Kit Status MenuProcedure to View Event History Event LogRDC2 Controller Operation TP-6880 10/14 DC2 Generator Set/ Transfer Switch Controller DC2 Controller OperationController Keypad Button Button FunctionLED Indication Description5Status Displays, Generator Running Exerciser Reset Exercise ModesMaintenance Timer OnCue Plus PasswordDC2 Controller Operation TP-6880 10/14 Scheduled Maintenance Scheduled Maintenance Service Schedule Oil Change Procedure Lubrication SystemEngine Oil Recommendation Low Oil Pressure ShutdownReset the maintenance timer on the controller Drain the oilReplace the oil filter Fill with oilResetting the Maintenance Timer Spark PlugsModel Resv RDC2 Model Resvl DC2Paper Element Service Air Cleaner ServiceAir Cleaner, 8RESV/RESVL Models Air Cleaner, 10/12RESV/RESVL Models Cooling SystemHazardous noise Can cause hearing loss EZ-273000-J Storage Procedure Scheduled Maintenance TP-6880 10/14 Troubleshooting Fault MessagesIntroduction USB PortTroubleshooting Problem Possible Cause Corrective ActionAppendix a Abbreviations AnsiLCB Page TP-6880 10/14