Kohler 8/10/12RESVL manual RDC2 Controller Features

Page 14

RDC2 Controller Features

DSix-button keypad

d OFF, AUTO, and RUN pushbuttons

dSelect and arrow buttons for access to system configuration and adjustment menus

DLED indicators for OFF, AUTO, and RUN modes

DLED indicators for utility power and generator set source availability and ATS position (Model RXT transfer switch required)

DLCD display

d Two lines x 16 characters per line

d Backlit display with adjustable contrast for excellent visibility in all lighting conditions

DScrolling system status display

d Generator set status d Voltage and frequency d Engine temperature d Oil pressure

d Battery voltage

d Engine runtime hours

DDate and time displays

DSmart engine cooldown senses engine temperature

D Digital isochronous governor to maintain steady-state speed at all loads

DDigital voltage regulation: ±0.5% RMS no-load to full-load

DAutomatic start with programmed cranking cycle

D Programmable exerciser can be set to start automatically on any future day and time, and run every week or every two weeks

DExercise modes

d Unloaded weekly exercise with complete system diagnostics

d Unloaded full-speed exercise

dLoaded full-speed exercise (Model RXT ATS required)

DFront-access mini USB connector for SiteTecht connection or the Kohler USB utility

DIntegral Ethernet connector for Kohlerr OnCuer Plus

DBuilt-in 2.5 amp battery charger

D Remote two-wire start/stop capability for optional connection of Model RDT or RSB transfer switches

DDiagnostic messages

dDisplays diagnostic messages for the engine, generator, Model RXT transfer switch, programmable interface module (PIM), and load control module (LCM) or load shed kit

dOver 70 diagnostic messages can be displayed

DMaintenance reminders

DSystem settings

d System voltage, frequency, and phase d Voltage adjustment

d Measurement system, English or metric

DATS status (Model RXT ATS required)

d Source availability

d ATS position (normal/utility or emergency/generator)

d Source voltage and frequency

DATS control (Model RXT ATS required)

d Source voltage and frequency settings d Engine start time delay

d Transfer time delays d Voltage calibration

d Fixed pickup and dropout settings

D Programmable Interface Module (PIM) status displays

dInput status (active/inactive) d Output status (active/inactive)

DLoad control module (LCM) or load shed kit menus

d Load status d Test function

14 Section 1 Descriptions and Service Views

TP-6880 10/14

Image 14
Contents RDC2 TP-6880 10/14aGenerator Set Identification Numbers Accessory Number Accessory DescriptionProduct Identification Information Controller IdentificationTable of Contents DC2 Controller Operation Scheduled MaintenanceTroubleshooting Accidental Starting Safety Precautions and InstructionsBattery Accidental starting Can cause severe injury or deathCarbon monoxide Can Cause Engine Backfire/Flash FireExhaust System Fire Can cause severe injury or deathFuel System Hazardous Noise Hazardous voltage Will cause severe injury or deathHeavy Equipment Hot PartsIntroduction Transfer Switch LiteratureAccessory Literature List of Related LiteratureGenerator Set Application NameplateEmission Information Emission Compliance PeriodService Assistance Service Assistance TP-6880 10/14 Descriptions and Service Views RDC2 Controller Features DC2 Controller Features Programmable Interface Module PIM AccessoriesCarburetor Heater Load Control Module LCMService Views 12143Service View Prestart Checklist Generator Set OperationGenerator Set Operation TP-6880 10/14 Exercising the Generator Set Generator Set OperationUnloaded Cycle Exercise with Complete System Diagnostics Automatic Operation with Other Transfer SwitchesSetting the Exerciser ExerciseUnloaded Full-Speed Exercise Power Failure During Exercise CycleSystem Diagnostics Loaded Full-Speed Exercise with RXT onlyResetting the Controller after a Fault Shutdown FaultsATS Communication Errors ShutdownsFault Message Shutdown SD Condition Check 3Controller Fault Messages Fault Shutdown SD Condition CheckGenerator Enclosure Thermostat Generator Set Operation TP-6880 10/14 RDC2 Controller Operation RDC2 Generator Set/ Transfer Switch ControllerControls and Indicators Button Function Controller Keypad LED IndicatorsButton LED OperationLCD Display Active AlertChanging Settings Controller PowerBattery Charging Procedure to Change SettingsChanging Settings on the RDC2 Controller 7Changing SettingsChanging the Exercise Settings Setting the ExerciserSetting the Exerciser at Controller Power-up Procedure to Set the Exerciser8Procedure to Set the Exerciser on the RDC2 Controller RDC2 Controller Menus Main MenuOverview Menu Engine Metering MenuGenerator Metering Menu Voltage CalibrationGenerator Set Information Menu Genset Run Time MenuGenset System Menu Setting the ExerciserAdjusting the Display Contrast Voltage Regulator VR Voltage AdjATS Status Menu Screens on this page do not appearATS Configuration Menu Changing ATS Configuration SettingsDate and Time Menu Networking Information MenusNetworking Status Submenu DhcpDhcp Submenu Networking Configuration Submenu OnCue Plus PasswordPassword 21Network Configuration Submenu Rbus Information 22RBUS Information SubmenuRemote Devices Submenu From FigureProgrammable Interface Module PIM Status Menu Load Control Module LCM or Load Shed Kit Menus 25Load Control Module LCM or Load Shed Kit Status MenuProcedure to View Event History Event LogRDC2 Controller Operation TP-6880 10/14 DC2 Generator Set/ Transfer Switch Controller DC2 Controller OperationLED Indication Controller KeypadButton Button Function Description5Status Displays, Generator Running Exerciser Reset Exercise ModesMaintenance Timer OnCue Plus PasswordDC2 Controller Operation TP-6880 10/14 Scheduled Maintenance Scheduled Maintenance Service Schedule Engine Oil Recommendation Oil Change ProcedureLubrication System Low Oil Pressure ShutdownReplace the oil filter Reset the maintenance timer on the controllerDrain the oil Fill with oilModel Resv RDC2 Resetting the Maintenance TimerSpark Plugs Model Resvl DC2Paper Element Service Air Cleaner ServiceAir Cleaner, 8RESV/RESVL Models Air Cleaner, 10/12RESV/RESVL Models Cooling SystemHazardous noise Can cause hearing loss EZ-273000-J Storage Procedure Scheduled Maintenance TP-6880 10/14 Introduction TroubleshootingFault Messages USB PortTroubleshooting Problem Possible Cause Corrective ActionAppendix a Abbreviations AnsiLCB Page TP-6880 10/14