Kohler 8/10/12RESVL manual RDC2 Controller Menus, Main Menu

Page 36

3.7 RDC2 Controller Menus

Controller menus display power system information, including status information for the engine, generator, and optional RBUS accessories, exercise settings, and event history. Some menus allow changes to the controller settings. Status information, including the engine runtime, cannot be changed by the operator.

Diagrams in the following sections show how to navigate through the menus.

Note: Use caution when navigating the controller menus. In some menus, pressing the Select button can enable editing of the controller settings. Changing the settings to incorrect values can adversely affect generator set operation or render the unit inoperable.

If a setting on the controller display is flashing, edit mode has been enabled. Press the OFF or AUTO button to exit the edit mode.

3.8 Main Menu

Press the Select button once to bring up the main menu. Overview is displayed. See Figure 3-9. Press the down arrow button to step to the next menu, Engine Metering. Use the UP and DOWN arrow buttons to step up and down through the menus shown in Figure 3-9.

The controller will exit the main menu after 5 minutes if no buttons are pressed. To exit the main menu immediately, press the controller’s OFF or AUTO button.

Status	Overview ---->
Displays	1.2 h

Press the Up and Down arrow buttons to move between menus.

Press OFF or AUTO to exit the menus.

Engine ---->

Metering

Generator---->

Metering

ATS ---->

Configuration *

Date ---->

and Time

Genset	---->
Information
Genset	---->
Run Time
Genset	---->
System
ATS	---->
Status

*ATS Configuration appears only if a Model RXT transfer switch is connected. [ PIM Status appears only if a programmable interface module is connected.

] Load Control appears only if a load control module (LCM) or load shed kit is connected.

Network ---->

Information

PIM ---->

Status [

Load ---->

Control ]

Event Log---->

tp6804

Figure 3-9RDC2 Main Menu

36 Section 3 RDC2 Controller Operation

TP-6880 10/14

Image 36

Contents RDC2 TP-6880 10/14aAccessory Number Accessory Description Product Identification InformationGenerator Set Identification Numbers Controller IdentificationTable of Contents Scheduled Maintenance TroubleshootingDC2 Controller Operation Safety Precautions and Instructions BatteryAccidental Starting Accidental starting Can cause severe injury or deathEngine Backfire/Flash Fire Exhaust SystemCarbon monoxide Can Cause Fire Can cause severe injury or deathFuel System Hazardous Noise Hazardous voltage Will cause severe injury or deathHeavy Equipment Hot PartsTransfer Switch Literature Accessory LiteratureIntroduction List of Related LiteratureNameplate Emission InformationGenerator Set Application Emission Compliance PeriodService Assistance Service Assistance TP-6880 10/14 Descriptions and Service Views RDC2 Controller Features DC2 Controller Features Accessories Carburetor HeaterProgrammable Interface Module PIM Load Control Module LCMService Views 12143Service View Prestart Checklist Generator Set OperationGenerator Set Operation TP-6880 10/14 Exercising the Generator Set Generator Set OperationAutomatic Operation with Other Transfer Switches Setting the ExerciserUnloaded Cycle Exercise with Complete System Diagnostics ExercisePower Failure During Exercise Cycle System DiagnosticsUnloaded Full-Speed Exercise Loaded Full-Speed Exercise with RXT onlyFaults ATS Communication ErrorsResetting the Controller after a Fault Shutdown ShutdownsFault Message Shutdown SD Condition Check 3Controller Fault Messages Fault Shutdown SD Condition CheckGenerator Enclosure Thermostat Generator Set Operation TP-6880 10/14 RDC2 Generator Set/ Transfer Switch Controller Controls and IndicatorsRDC2 Controller Operation Controller Keypad LED Indicators ButtonButton Function LED OperationLCD Display Active AlertController Power Battery ChargingChanging Settings Procedure to Change SettingsChanging Settings on the RDC2 Controller 7Changing SettingsSetting the Exerciser Setting the Exerciser at Controller Power-upChanging the Exercise Settings Procedure to Set the Exerciser8Procedure to Set the Exerciser on the RDC2 Controller RDC2 Controller Menus Main MenuOverview Menu Engine Metering MenuGenerator Metering Menu Voltage CalibrationGenerator Set Information Menu Genset Run Time MenuSetting the Exerciser Adjusting the Display ContrastGenset System Menu Voltage Regulator VR Voltage AdjATS Status Menu Screens on this page do not appearATS Configuration Menu Changing ATS Configuration SettingsDate and Time Menu Networking Information MenusNetworking Status Submenu DhcpNetworking Configuration Submenu OnCue Plus Password PasswordDhcp Submenu 21Network Configuration Submenu Rbus Information 22RBUS Information SubmenuRemote Devices Submenu From FigureProgrammable Interface Module PIM Status Menu Load Control Module LCM or Load Shed Kit Menus 25Load Control Module LCM or Load Shed Kit Status MenuProcedure to View Event History Event LogRDC2 Controller Operation TP-6880 10/14 DC2 Generator Set/ Transfer Switch Controller DC2 Controller OperationController Keypad Button Button FunctionLED Indication Description5Status Displays, Generator Running Exerciser Reset Exercise ModesMaintenance Timer OnCue Plus PasswordDC2 Controller Operation TP-6880 10/14 Scheduled Maintenance Scheduled Maintenance Service Schedule Oil Change Procedure Lubrication SystemEngine Oil Recommendation Low Oil Pressure ShutdownReset the maintenance timer on the controller Drain the oilReplace the oil filter Fill with oilResetting the Maintenance Timer Spark PlugsModel Resv RDC2 Model Resvl DC2Air Cleaner Service Air Cleaner, 8RESV/RESVL ModelsPaper Element Service Air Cleaner, 10/12RESV/RESVL Models Cooling SystemHazardous noise Can cause hearing loss EZ-273000-J Storage Procedure Scheduled Maintenance TP-6880 10/14 Troubleshooting Fault MessagesIntroduction USB PortTroubleshooting Problem Possible Cause Corrective ActionAppendix a Abbreviations AnsiLCB Page TP-6880 10/14